A 1.95-kg falcon catches and holds onto a 0.655-kg dove from behind in midair.
what is their final speed, in meters per second, after impact if the falcon’s speed is initially 28.5 m/s and the dove’s speed is 8.5 m/s in the same direction?

The position of the image formed by the first lens can be calculated using the thin lens equation:

[tex]1/f = 1/d_o + 1/d_i[/tex]

where f is the focal length of the lens, d is the object distance (distance of the object from the lens), and is the image distance (distance of the image from the lens). We can solve for  d.

[tex]1/d_i = 1/f - 1/d_o[/tex]

[tex]d_i = 1 / (1/f - 1/d_o)[/tex]

For the first lens, f = 12.5 cm and d_o = 16.4 cm. Substituting these values, we get:

[tex]d_i = 1 / (1/12.5 - 1/16.4) = 26.5 cm[/tex]

Therefore, the position of the image formed by the first converging lens is 26.5 cm to the right of the first lens.

Learn more about magnification here:

https://brainly.com/question/21370207

#SPJ11

The induced current in the coil behaves in such a way that it opposes the motion of the falling magnet with the north pole facing down.

This can be further explained through the following steps:

1. As the magnet falls, its motion generates a changing magnetic field within the coil.
2. According to Faraday's Law of Electromagnetic Induction, this changing magnetic field induces an electromotive force (EMF) in the coil.
3. The direction of the induced current is determined by Lenz's Law, which states that the induced current will flow in such a way as to oppose the change in magnetic flux.
4. Since the north pole of the magnet is facing down, the induced current will flow in a direction to create a magnetic field with a north pole facing up, to oppose the downward motion of the magnet.
5. The induced current increases as the magnet approaches the center of the coil because the rate of change of magnetic flux increases.
6. When the magnet reaches the center of the coil, the induced current is at its maximum.
7. As the magnet continues to fall and moves away from the center of the coil, the induced current decreases because the rate of change of magnetic flux decreases.
8. When the magnet has completely exited the coil, the induced current becomes zero as there is no more change in magnetic flux.
In summary, the induced current in the coil behaves in such a way that it opposes the motion of the falling magnet with the north pole facing down. The current increases as the magnet approaches the center of the coil and decreases as it moves away from it, becoming zero when the magnet exits the coil.

Learn more about the magnet: https://brainly.com/question/27862911

#SPJ11

To determine the force in each member of the loaded truss, we need to consider the tension and compression forces acting on each member.

Forces are positive if in tension and negative if in compression.
Using the symmetry of the truss and of the loading, we can see that members AB, AH, and GH are all in tension, while members BC, BH, CD, CF, CG, DE, DF, EF, FG, and NG are all in compression.
Therefore, the force in each member is:
AB = +10 kN; AH = +10 kN ; BC = -10 kN ; BH = -10 kN; CD = -20 kN ; CF = -20 kN ; CG = -20 kN; CH = -20 kN ; DE = -10 kN ; DF = -10 kN ; EF = -10 kN ; FG = -20 kN ; GH = +10 kN ; NG = -20 kN
Note that the negative sign indicates compression forces, while the positive sign indicates tension forces.

learn more about Forces Refer: https://brainly.com/question/13191643

#SPJ11

The climate tipping point at 450 ppm (parts per million) refers to a threshold concentration of carbon dioxide (CO2) in the atmosphere, beyond which there is a higher risk of triggering irreversible and catastrophic changes in the Earth's climate system. The 450 ppm target has been widely discussed as a goal for limiting global warming to 2 degrees Celsius above pre-industrial levels.

The climate tipping point refers to a threshold in the Earth's climate system. Beyond this, there is a higher risk of triggering irreversible and potentially catastrophic changes. The tipping point can occur when positive feedback mechanisms, such as melting ice caps, increasing forest fires, and accelerating global warming.

Learn more about climate tipping point: https://brainly.com/question/30928277

#SPJ11

The frequency of the guitar is 194 Hz, and the frequency of the tuner is 195 Hz, so the beat frequency is |194 Hz - 195 Hz| = 1 Hz

Therefore, the beat frequency is 1 Hz.

Frequency is the number of revolutions of a periodic wave that occur per unit of time. It is often measured in Hertz (Hz), representing the number of cycles per second. For example, if a sound wave completes 440 revolutions in one second, its frequency would be 440 Hz.

Electromagnetic radiation refers to the energy that travels through space through oscillating electric and magnetic fields. This type of radiation includes many kinds of waves, such as radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays.

To learn more about waves, click here:

https://brainly.com/question/25954805

#SPJ1

20 Wh of electrical energy is required to make a slice of toast using a 1200-W toaster and it costs approximately 0.14 cents to make a slice of toast at a rate of 7.0 cents/kW·h.

To calculate the electrical energy needed to make a slice of toast using a 1200-W toaster, we first need to convert the cooking time to hours. One minute is equal to 1/60 of an hour. Now, we can use the formula for electrical energy: Energy = Power × Time.

Energy = 1200 W × (1/60) h = 20 Wh (Watt-hours)

So, 20 Wh of electrical energy is required to make a slice of toast using a 1200-W toaster.

Next, let's determine the cost of using the toaster for 1 minute at a rate of 7.0 cents/kW·h. First, convert the energy used from Wh to kWh:

20 Wh = 0.02 kWh

Now, multiply the energy used (in kWh) by the cost per kWh:

Cost = 0.02 kWh × 7.0 cents/kWh = 0.14 cents

Therefore, it costs approximately 0.14 cents to make a slice of toast using a 1200-W toaster at a rate of 7.0 cents/kW·h.

For more such questions on Electrical energy.

https://brainly.com/question/30544779#

#SPJ11

The average distance and the most probable distance of an electron from the nucleus in the 1s orbital of a hydrogen atom are 1.5a₀ and a₀ respectively. The correct answer is option A.

In the 1s orbital of a hydrogen atom, the average distance (⟨r⟩) and the most probable distance (r_max) of an electron from the nucleus can be calculated using the Bohr model and the radial distribution function.

For the 1s orbital, the average distance is given by:
⟨r⟩ = 3/2 * a₀

The most probable distance (r_max) corresponds to the maximum value of the radial distribution function, which occurs at the Bohr radius for the 1s orbital:
r_max = a₀

So, the average distance is 1.5a₀, and the most probable distance is a₀.

Therefore option A is the correct answer.

Learn more about the Bohr model:
https://brainly.com/question/28700833

#SPJ11

The required order of the active lowpass filter is at least third-order to meet the stopband requirement of -20 dB at 600 Hz while maintaining a cutoff frequency of 500 Hz.

To explain further, an active lowpass filter is a type of electronic filter that allows low-frequency signals to pass through while attenuating high-frequency signals. The cutoff frequency of the filter is the frequency at which the output power is half the input power. The stopband is the frequency range above the cutoff frequency where the filter should attenuate the signal. In this case, the stopband is defined as being -20 dB from the passband at 600 Hz.

The order of the filter is related to its complexity and determines its ability to attenuate signals in the stopband. Higher-order filters have a steeper roll-off (i.e., faster attenuation of frequencies above the cutoff) and better attenuation in the stopband. A third-order filter is the minimum order required to meet the stopband requirement of -20 dB at 600 Hz while maintaining a cutoff frequency of 500 Hz.

To know more about lowpass filter, here

brainly.com/question/31492375

#SPJ4

--The complete question is, What is the required order of an active lowpass filter that has a cutoff frequency of 500 Hz and meets the stopband requirement of -20 dB at 600 Hz?--

1. Possible. The outcome is possible because the white ball transfers all its momentum to the grey ball, which then moves in the opposite direction with the same speed.

2. Not possible. The outcome is not possible because the final velocities violate the law of conservation of momentum. The white ball has a higher final velocity than the initial velocity, which would require an external force.

Initial momentum = [tex]m_B * v_B + m_D * v_D[/tex] =[tex](60 kg) * (10 m/s) + (65 kg) * (-6 m/s) = 210 kg m/s[/tex]

Final momentum = [tex](m_B + m_D) * v_final[/tex]

We can solve for the final velocity of the system:

v_final = [tex](m_B * v_B + m_D * v_D) / (m_B + m_D) = (60 kg * 10 m/s - 65 kg * 6 m/s) / 125 kg = 0.88 m/s[/tex]

Therefore, the final velocity of Drew and Blake is 0.88 m/s.

For the second problem, we can use conservation of momentum again, since there are no external forces acting on the system.

Initial momentum = 0

Final momentum = [tex]m_astronaut * v_astronaut + m_toolkit * v_toolkit[/tex]

We can solve for the final velocity of the astronaut:

[tex]v_astronaut = - (m_toolkit * v_toolkit) / m_astronaut = - (18 kg * 2 m/s) / 115 kg = -0.31 m/s[/tex]

An external force is any force that acts on an object or a system from outside of the system. It can be a contact force, such as a push or pull from a person or an object, or a non-contact force, such as gravity, electromagnetic force, or pressure from a fluid.

External forces can change the state of motion or deformation of an object or a system, and they can cause acceleration, deceleration, or deformation of the object. In the absence of external forces, an object or a system would maintain its state of motion or rest according to the law of inertia. External forces are important in many areas of physics, including mechanics, electromagnetism, thermodynamics, and fluid dynamics.

To learn more about External forces visit here:

brainly.com/question/29130400

#SPJ4

1. Possible. The outcome is possible because the white ball transfers all its momentum to the grey ball, which then moves in the opposite direction with the same speed.

2. Not possible. The outcome is not possible because the final velocities violate the law of conservation of momentum. The white ball has a higher final velocity than the initial velocity, which would require an external force.

Initial momentum = [tex]m_B * v_B + m_D * v_D[/tex] =[tex](60 kg) * (10 m/s) + (65 kg) * (-6 m/s) = 210 kg m/s[/tex]

Final momentum = [tex](m_B + m_D) * v_final[/tex]

We can solve for the final velocity of the system:

v_final = [tex](m_B * v_B + m_D * v_D) / (m_B + m_D) = (60 kg * 10 m/s - 65 kg * 6 m/s) / 125 kg = 0.88 m/s[/tex]

Therefore, the final velocity of Drew and Blake is 0.88 m/s.

For the second problem, we can use conservation of momentum again, since there are no external forces acting on the system.

Initial momentum = 0

Final momentum = [tex]m_astronaut * v_astronaut + m_toolkit * v_toolkit[/tex]

We can solve for the final velocity of the astronaut:

[tex]v_astronaut = - (m_toolkit * v_toolkit) / m_astronaut = - (18 kg * 2 m/s) / 115 kg = -0.31 m/s[/tex]

An external force is any force that acts on an object or a system from outside of the system. It can be a contact force, such as a push or pull from a person or an object, or a non-contact force, such as gravity, electromagnetic force, or pressure from a fluid.

External forces can change the state of motion or deformation of an object or a system, and they can cause acceleration, deceleration, or deformation of the object. In the absence of external forces, an object or a system would maintain its state of motion or rest according to the law of inertia. External forces are important in many areas of physics, including mechanics, electromagnetism, thermodynamics, and fluid dynamics.

To learn more about External forces visit here:

brainly.com/question/29130400

#SPJ4

Lahars occur on (A). volcanic slopes is correct option because Lahars, also known as volcanic mudflows, are fast-moving mixtures of rock debris, volcanic ash, and water that can occur during or after a volcanic eruption.

They are typically triggered by heavy rainfall or the rapid melting of snow and ice on the volcano, which mixes with loose volcanic material on the slopes and forms a slurry that can flow rapidly down the slope. Lahars can travel many kilometers from the volcano and cause significant damage to infrastructure and communities in their path.

A streaming mixture of water and pyroclastic material is referred to as a lahar. It does not allude to a specific concentration of sediment or rheology. Lahars can take the form of regular stream flows (less than 30% sediment concentration), hyper-concentrated stream flows (between 30 and 60% sediment concentration), or debris flows (more than 60% sediment concentration).

Therefore, the correct option is (A).

To know more about volcanic

https://brainly.com/question/14530257

#SPJ4

To produce an acceleration of 0.805 m/s2 upwards against a 175-n frictional force, the elevator's cable must supply a force of 701.5 newtons.

This is calculated using the formula

F = ma,

where F is the force, m is the mass (which we assume to be the mass of the elevator plus any occupants), and a is the acceleration.

We also need to take into account the frictional force acting against the elevator, which is subtracted from the force supplied by the cable.

Therefore, the equation becomes

F - 175 = ma.

Plugging in the given values,

we get

F - 175 = (m)(0.805).

Solving for F,

we get

F = (m)(0.805) + 175.

Since we don't know the exact mass of the elevator, we can't calculate the exact force needed. However, we can say that the force must be at least 701.5 newtons to achieve the given acceleration and overcome the frictional force.

To know more about frictional force click here:

https://brainly.com/question/30280752

#SPJ11

To determine the tensile stress in two square bars welded together, you will need to calculate the cross-sectional area of the welded joint.

This can be done by measuring the width and thickness of the bars and subtracting any material that has been removed during the welding process. Once you have the cross-sectional area, you can divide the applied load by the area to calculate the tensile stress.

Keep in mind that the tensile stress will vary depending on the type of welding used, the strength of the base materials, and the orientation of the bars relative to the applied load. It is important to consult with a qualified engineer or welding specialist to ensure that the joint is designed and fabricated properly to withstand the intended loads.

To determine the tensile stress in two square bars welded together, you will need to consider the following terms: cross-sectional area, force applied, and tensile stress formula.

First, find the cross-sectional area of each square bar by multiplying the side length by itself (A = side^2). Then, add the two areas together to get the total cross-sectional area (A_total = A1 + A2).

Next, determine the force applied (F) on the welded bars. This is typically given or can be calculated based on the specific problem.

Finally, use the tensile stress formula, which is stress (σ) equals force (F) divided by the total cross-sectional area (A_total): σ = F / A_total. By plugging in the values you found earlier, you can calculate the tensile stress in the two square bars welded together.

To learn more about force click here

brainly.com/question/30751496

#SPJ11

the electrons move with a velocity of 3.7 × 10 7 m/s. what electric field strength is needed to accelerate electrons from rest to this velocity in a distance of 5.0 mm So, an electric field strength of approximately 1.84 × 10^7 N/C

To find the electric field strength needed to accelerate electrons from rest to a velocity of 3.7 × 10^7 m/s in a distance of 5.0 mm, we can follow these steps:

1. First, let's recall the kinematic equation for motion under constant acceleration: v^2 = u^2 + 2as, where v is the final velocity, u is the initial velocity, a is the acceleration, and s is the distance traveled.

2. Since the electrons start from rest, their initial velocity (u) is 0. Plug in the given values: (3.7 × 10^7 m/s)^2 = 0^2 + 2a(5.0 × 10^-3 m).

3. Solve for acceleration (a): a = (3.7 × 10^7 m/s)^2 / (2 × 5.0 × 10^-3 m).

4. Calculate the acceleration: a ≈ 2.73 × 10^15 m/s^2.

5. Now, let's use the formula for the force on an electron in an electric field: F = qE, where F is the force, q is the charge of the electron (1.6 × 10^-19 C), and E is the electric field strength.

6. We also know that F = ma, where m is the mass of the electron (9.11 × 10^-31 kg). So, ma = qE.

7. Plug in the values for the mass of the electron, its charge, and the calculated acceleration: (9.11 × 10^-31 kg)(2.73 × 10^15 m/s^2) = (1.6 × 10^-19 C)E.

8. Solve for the electric field strength (E): E ≈ 1.84 × 10^7 N/C.

So, an electric field strength of approximately 1.84 × 10^7 N/C is needed to accelerate electrons from rest to a velocity of 3.7 × 10^7 m/s in a distance of 5.0 mm.

Learn more about electric field strength at  brainly.com/question/15170044

#SPJ11

The correct option is A,  the equivalent capacitance of this arrangement is 2C/3.

When two identical capacitors with capacitance C are connected in parallel, the equivalent capacitance is:

C_parallel = C + C = 2C

When this combination is connected in series with a third identical capacitor with capacitance C, the equivalent capacitance is:

1/C_series = 1/C_parallel + 1/C = 1/2C + 1/C = 3/2C

By multiplying both sides reciprocally, we obtain:

C_series = 2/3C

A system's capacitance is its capacity to hold an electric charge. It is a fundamental characteristic of capacitors, passive electrical parts used in electronic circuits for a variety of functions, including energy storage and signal filtering, and is measured in Farads (F).

A capacitor's capacitance is influenced by a number of variables, such as the distance between the plates, the size of the plates, and the dielectric constant of the material separating the plates. More charge may be stored in a capacitor with a big capacitance than one with a small capacitance.  Numerous applications, including power factor correction, filtering, and energy storage, depend heavily on capacitance.

To learn more about Capacitance visit here:

brainly.com/question/28445252

#SPJ4

Complete Question:-

Two identical capacitors, each with capacitance C, are connected in parallel and the combination is connected in series to a third identical capacitor. The equivalent capacitance of this arrangement is:

A. 2C/3

B. C

C. 3C/2

D. 2C

E. 3C

The magnetic force experienced by the 47.5 cm wire is approximately 4.59 N.

The magnetic force (F) on a wire can be calculated using the formula:

F = I * L * B * sinθ

where I is the current in the wire (in Amperes), L is the length of the wire (in meters), B is the magnetic field strength (in Teslas), and θ is the angle between the current and magnetic field directions. In your case, I = 7.5 A, B = 1.3 T, L = 47.5 cm (0.475 m), and since the angle isn't specified, we'll assume the current and magnetic field are perpendicular, meaning θ = 90° and sinθ = 1.

Now, we can plug the values into the formula:

F = (7.5 A) * (0.475 m) * (1.3 T) * (1)

F ≈ 4.59375 N

Therefore, the magnetic force that the 47.5 cm wire is subjected to is roughly 4.59 N.

Learn more about "magnetic field": https://brainly.com/question/7802337

#SPJ11

Therefore, the battery will last for approximately 141.2 seconds if the voltage remains constant.

Here Terminal voltage of the battery, δv = 1.6 V

Energy contained in the battery, E = 1.2 kJ = 1200 J

Power consumed by the light bulb, P = 8.5 W

Part (a) The power consumed by a device can be given by the equation P = δ[tex]v^2[/tex] / R, where R is the resistance of the device. Substituting the given values, we get:

8.5 W =[tex](1.6 V)^2[/tex] / R

Rearranging the equation, we get:

R = [tex](1.6 V)^2[/tex] / 8.5 W

Part (b) Substituting values, we get:

[tex]R = (1.6 V)^2 / 8.5 W[/tex]

= 0.302 ohms (approximately)

Therefore, the resistance of the light bulb is approximately 0.302 ohms.

(c): The energy contained in the battery can be used to supply power to the light bulb for a certain amount of time. This time can be calculated using the equation:

E = P × t

t is the time in seconds. Rearranging the equation, we get:

t = E / P

Substituting values, we get:

t = 1200 J / 8.5 W = 141.2 seconds (approximately)

Learn more about voltage visit: brainly.com/question/27861305

#SPJ4

a. The potential difference between the top and the bottom of the truck's side panels is approximately 0.0021 V.
b. The tops of the panels will be positive relative to the bottoms.

We will be using the formula for the potential difference induced in a conductor moving through a magnetic field, which is given by:
ΔV = B * L * v
where ΔV is the potential difference, B is the magnetic field, L is the length of the conductor (in this case, the height of the truck's side panels), and v is the velocity of the conductor.
a. To find the potential difference between the top and the bottom of the truck's side panels, we first need to convert the truck's speed from km/hr to m/s:
60 km/hr * (1000 m/km) * (1 hr / 3600 s) = 16.67 m/s
Now we can plug in the given values:
ΔV = [tex](5.0 * 10^{-5} T) * (2.5 m) * (16.67 m/s)[/tex]
ΔV ≈ 0.0021 V
So, the potential difference between the top and the bottom of the truck's side panels is approximately 0.0021 V.
b. To determine the sign of the potential difference, we can use the right-hand rule. Point your right thumb in the direction of the truck's motion (west), and your fingers in the direction of the magnetic field (north). Your palm will face upwards, which indicates that the top of the panels will be positive relative to the bottoms.

To learn more about potential difference click here https://brainly.com/question/12198573

#SPJ11

a. The potential difference between the top and the bottom of the truck's side panels is approximately 0.0021 V.
b. The tops of the panels will be positive relative to the bottoms.

We will be using the formula for the potential difference induced in a conductor moving through a magnetic field, which is given by:
ΔV = B * L * v
where ΔV is the potential difference, B is the magnetic field, L is the length of the conductor (in this case, the height of the truck's side panels), and v is the velocity of the conductor.
a. To find the potential difference between the top and the bottom of the truck's side panels, we first need to convert the truck's speed from km/hr to m/s:
60 km/hr * (1000 m/km) * (1 hr / 3600 s) = 16.67 m/s
Now we can plug in the given values:
ΔV = [tex](5.0 * 10^{-5} T) * (2.5 m) * (16.67 m/s)[/tex]
ΔV ≈ 0.0021 V
So, the potential difference between the top and the bottom of the truck's side panels is approximately 0.0021 V.
b. To determine the sign of the potential difference, we can use the right-hand rule. Point your right thumb in the direction of the truck's motion (west), and your fingers in the direction of the magnetic field (north). Your palm will face upwards, which indicates that the top of the panels will be positive relative to the bottoms.

To learn more about potential difference click here https://brainly.com/question/12198573

#SPJ11

The critical angle for total internal reflection (α_crit) is approximately 66.2 degrees.

To calculate the critical angles for total internal reflection in a fiber optic cable, we can use Snell's Law and the given index of refraction values for the core (n_core = 1.51) and the cladding (n_clad = 1.38).

For total internal reflection to occur, the critical angle (α_crit) is found using the following formula:

sin(α_crit) = n_clad / n_core

Plugging in the given values:

sin(α_crit) = 1.38 / 1.51 ≈ 0.9139

To find the critical angle in degrees, we can take the inverse sine of this value:

α_crit = arcsin(0.9139) ≈ 66.2 degrees

So, the critical angle for total internal reflection (α_crit) is approximately 66.2 degrees.

To learn more about reflection, refer below:

https://brainly.com/question/30270479

#SPJ11

The total energy (kinetic plus rest energy) of the particle is  9.3 × 10⁻¹⁰ J.

Given:

The rest mass of particle is E(rest) = 6.64 × 10⁻²⁷ kg

Momentum is p =  2.10 × 10⁻¹⁸ kg m/s

The total energy can be expressed as follows:

E(t) = K + E(rest)   .....(1)

The kinetic energy is computed by using the below relation:

K = (1/2) × p²/m

Substitute the given values in the above relation, and we get:

K = (1/2) × (2.10 × 10⁻¹⁸)²/6.64 × 10⁻²⁷

K = 3.32 × 10⁻¹⁰ J   .....(2)

The rest energy is computed by using the below relation:

E(rest) = mc²

Substitute the given values in the above relation, and we get:

E(rest) = 6.64 × 10⁻²⁷ × (3 × 10⁸)

E(rest) = 5.98 × 10⁻¹⁰ J   .....(3)

From equation (1),

E(t) = 3.32 × 10⁻¹⁰ J + 5.98 × 10⁻¹⁰

E(t) = 9.3 × 10⁻¹⁰ J

Learn more about the total energy here:

https://brainly.com/question/31969020

#SPJ12

Approximately 8.4151% of the mechanical energy of the oscillator is lost in each cycle at the given amplitude.

The amplitude of a lightly damped oscillator decreases by 4.3% during each cycle.

To find the percentage of mechanical energy lost in each cycle, we need to consider the relationship between amplitude and energy.

Energy in an oscillator is proportional to the square of its amplitude (E ∝ A^2).

Since the amplitude decreases by 4.3%, we can represent the new amplitude as 0.957 times the original amplitude (100% - 4.3% = 95.7% = 0.957).

New energy (E_new) is proportional to the square of the new amplitude:

E_new ∝ (0.957 * A)^2

Now, we'll find the percentage of energy lost in each cycle by comparing the new energy to the original energy:

Percentage of energy lost = (1 - E_new/E) * 100%

Substituting the relationship between energy and amplitude:

Percentage of energy lost = (1 - (0.957 * A)^2 / A^2) * 100%

Simplifying the expression:

Percentage of energy lost = (1 - 0.957^2) * 100%

Calculating the percentage:

Percentage of energy lost ≈ (1 - 0.915849) * 100% ≈ 8.4151%

So, approximately 8.4151% of the mechanical energy of the oscillator is lost in each cycle.

For more information on amplitude, oscillator and energy refer to https://brainly.com/question/26114128

#SPJ11

The total angular distance after performing 10 complete squats is 2000°, and the angular displacement is 0°.

To find the total angular distance and angular displacement after performing 10 complete squats, we first need to understand the terms.

"Distance" refers to the total path covered, while "displacement" refers to the change in position from the starting point to the endpoint.

In this case, we are dealing with angular distance and angular displacement, which are measured in degrees (°).

Each complete squat has two phases: the down phase (100° of flexion) and the up phase (100° of extension).

Step 1: Calculate the angular distance covered in one complete squat.
Angular distance (one squat) = Down phase (100°) + Up phase (100°) = 200°

Step 2: Calculate the total angular distance after performing 10 complete squats.
Total angular distance (10 squats) = 200° (one squat) × 10 = 2000°

Step 3: Calculate the angular displacement after performing 10 complete squats.
Since the person returns to the starting position after each squat, the angular displacement after 10 complete squats is 0°.

In summary, the total angular distance after performing 10 complete squats is 2000°, and the angular displacement is 0°.

For more information on distance and displacement refer to https://brainly.com/question/321442

#SPJ11

The normal force exerted on the crate by the elevator is 960 N.

To find the normal force exerted on the crate (160 kg) by the elevator traveling upward and slowing down at 4 m/s², we need to consider the net force acting on the crate. Here are the steps,

1. Calculate the gravitational force (weight) acting on the crate: F_gravity = m * g
  where m is the mass (160 kg) and g is the acceleration due to gravity (10 m/s²).
  F_gravity = 160 kg * 10 m/s² = 1600 N (downward)

2. Calculate the net force acting on the crate due to the elevator's acceleration: F_net = m * a
  where m is the mass (160 kg) and a is the deceleration of the elevator (4 m/s²).
  F_net = 160 kg * 4 m/s² = 640 N (upward)

3. Calculate the normal force exerted on the crate: F_normal = F_gravity + F_net
  F_normal = 1600 N (downward) + 640 N (upward)
  Since the net force is upward, subtract the net force from the gravitational force:
  F_normal = 1600 N - 640 N = 960 N

The elevator typically applies 960 N of force to the crate.

Learn more about "normal force": https://brainly.com/question/2254109

#SPJ11

the shear force resisted by the web of the wide-flange beam is approximately 30,024 N.

To determine the shear force resisted by the web of the wide-flange beam, we first need to calculate the shear stress on the web.
Shear stress = Shear force / Cross-sectional area
The cross-sectional area of the web can be calculated as:
Area = thickness x width
Here, the width of the web (w) is given as 200 mm. We need to find the thickness of the web.
Assuming that the wide-flange beam is a W-shaped beam, we can use the standard dimensions for a W200x27 beam (where 200 is the depth of the beam in mm and 27 is the thickness of the web in mm).
Therefore, the cross-sectional area of the web would be:
Area = 27 x 200 = 5400 mm^2
Now, we can calculate the shear stress on the web as:
Shear stress = 30,000 N / 5400 mm^2 = 5.56 N/mm^2
Finally, we can calculate the shear force resisted by the web using the shear stress and the cross-sectional area of the web:
Shear force = Shear stress x Area

Shear force = 5.56 N/mm^2 x 5400 mm^2 = 30,024 N

Learn more about wide-flange here:

https://brainly.com/question/29357936

#SPJ11

The time required for light to travel vertically from the surface of the ice to the bottom of the pond is approximately 14.87 ns.

To find the time required, we need to consider the total distance traveled by light through the ice and water layers. The total distance is 2.95 m, with the ice layer being 0.28 m thick. First, we need to find the distance traveled by light through the water layer, which is 2.95 - 0.28 = 2.67 m.

Next, we need to know the speed of light in each medium. The speed of light in ice is about 2.25 x 10⁸ m/s, and in water, it's approximately 2.23 x 10⁸ m/s.

Now, we calculate the time taken in each layer:
Time in ice = (distance in ice) / (speed of light in ice) = 0.28 / (2.25 x 10⁸) = 1.244 x 10⁻⁹ s
Time in water = (distance in water) / (speed of light in water) = 2.67 / (2.23 x 10⁸) = 1.198 x 10⁻⁸ s

Finally, we add the times together and convert to nanoseconds:
Total time = (1.244 x 10^-9 + 1.198 x 10⁻⁸) x 10⁹ = 14.87 ns

To know more about speed of light click on below link:

https://brainly.com/question/1555553#

#SPJ11

The charge is 30 pC, when electric field has a magnitude of 3.0 N/C at the distance of 30 cm from point charge. Option B is correct.

We will use Coulomb's law to solve this problem;

Coulomb's law states that the magnitude of the electric field E created by a point charge Q at a distance r from the charge is given by;

E = k × Q / r²

where k is Coulomb's constant, which is approximately 9 x 10⁹ Nm²/C².

In this problem, we are given electric field having a magnitude of 3.0 N/C at a distance of 30 cm from a point charge. Converting 30 cm to meters, we have;

r = 0.3 m

Plugging the given values into Coulomb's law, we have;

3.0 N/C = (9 x 10⁹ Nm²/C²) × Q / (0.3 m)²

Solving for Q, we get;

Q = (3.0 N/C) × (0.3 m)² / (9 x 10⁹ Nm²/C²)

Q = 30 x 10⁻¹² C

Q = 30 pC

Therefore, the charge is 30 pC.

Hence, B. is the correct option.

To know more about electric field here

https://brainly.com/question/8971780

#SPJ4

If the wave speed decreases, the wavelength increases. Therefore, the wavelength changes by a factor of 3/4 when the wave speed decreases from c to (3/4)c.

This is because the speed of propagation of the wave is inversely proportional to its wavelength, as given by the formula c = fλ, where c is the speed of light, f is the frequency of the wave, and λ is its wavelength. Therefore, if c decreases, the wavelength must increase to keep the frequency constant.
If the wave speed decreases from c to (3/4)c, the wavelength increases by a factor of 4/3. This can be calculated using the same formula as above, but with the new speed of propagation substituted in: (3/4)c = f(4/3)λ. Solving for λ gives λ = (4/3)(c/f), which is (4/3) times the wavelength in the original medium.

(a) When an electromagnetic wave travels from one medium to another with a different speed of propagation, if the wave speed decreases, the wavelength will also decrease. This is because the frequency remains constant, and since the wave speed (v) is the product of frequency (f) and wavelength (λ), as described by the equation v = fλ, a decrease in wave speed while keeping the frequency constant will result in a decrease in the wavelength.
(b) In the case where the wave speed decreases from c to (3/4)c, the factor by which the wavelength changes can be determined by comparing the initial and final wave speeds and their relation to the wavelength. Initially, we have v1 = c = fλ1, and after the change, we have v2 = (3/4)c = fλ2. Since the frequency remains constant, we can divide the second equation by the first equation to find the factor by which the wavelength changes:
(λ2/λ1) = (v2/v1) = ((3/4)c)/c = 3/4
Therefore, the wavelength changes by a factor of 3/4 when the wave speed decreases from c to (3/4)c.

Visit here to learn more about electromagnetic wave:

brainly.com/question/3101711

#SPJ11

Using the parallel axis theorem, we can find the moment of inertia about the desired axis by adding the product of the mass and the square of the distance between the two axes, which is the distance between the center of mass and the desired axis.

The moment of inertia of a body is a measure of its resistance to rotational motion around a particular axis.

For a 2D square with mass concentrated along its perimeter, the moment of inertia can be calculated by dividing the square into small pieces, calculating the moment of inertia of each piece about the axis, and then summing up the contributions from all the pieces.

For this specific problem, we can use the parallel axis theorem to find the moment of inertia of the square about an axis perpendicular to the plane of the square at its center of mass.

The moment of inertia of the square about an axis passing through its center of mass can be calculated using the formula for a thin rectangular plate, which is I_cm = (1/12) M ([tex]a^{2}+b^{2}[/tex]), where M is the mass of the square, and a and b are the dimensions of the square.

Then, using the parallel axis theorem, we can find the moment of inertia about the desired axis by adding the product of the mass and the square of the distance between the two axes, which is the distance between the center of mass and the desired axis.

To know more about moment of inertia, refer here:

https://brainly.com/question/15246709#

#SPJ11

The estimated fatigue strength corresponding to the life of 150,000 cycles for this material is approximately 106.25 kpsi.

Estimate the fatigue strength for a life of 150,000 cycles. We will be using the modified Goodman's equation for this estimation, which is a common method for estimating fatigue strength. Here are the steps:

1. Determine the material's ultimate strength (Su): In this case, it's given as 250 kpsi.

2. Calculate the material's endurance limit (Se): Typically, for steel, the endurance limit is approximately half of the ultimate strength. So, in this case, Se = 250 kpsi / 2 = 125 kpsi.

3. Estimate the fatigue strength (Sf) corresponding to the life of 150,000 cycles using the modified Goodman's equation:

Sf = Se * (1 - (N / Nf))

Where:
Sf = fatigue strength at N cycles
Se = endurance limit
N = number of cycles (150,000 cycles)
Nf = fatigue life at the endurance limit (usually assumed as 1,000,000 cycles for steel)

4. Substitute the values and calculate Sf:

Sf = 125 kpsi * (1 - (150,000 / 1,000,000))
Sf = 125 kpsi * (1 - 0.15)
Sf = 125 kpsi * 0.85
Sf ≈ 106.25 kpsi

The estimated fatigue strength corresponding to the life of 150,000 cycles for this material is approximately 106.25 kpsi.

Know more about Fatigue Strength here:

https://brainly.com/question/31485413

#SPJ11

If a piece of metal initially at 10 degrees Celsius is heated until it has twice the internal energy, its final temperature will be 20 degrees Celsius. The final temperature of a piece of metal heated until it has twice the internal energy can be found by using the formula for Internal Energy.

Given, a metal piece is initially at 10 degrees Celsius, we need to find its final temperature when its internal energy is doubled.

The formula for internal energy,

U = C * T

where the internal energy (U) of an object is proportional to its temperature (T) and the object's heat capacity (C)

If the internal energy is doubled, we have 2 * U_initial = U_final. Since U_initial = C * T_initial and U_final = C * T_final

We can write the equation as 2 * (C * T_initial) = C * T_final.

Simplify the equation to 2 * T_initial = T_final.

Since the initial temperature is 10 degrees Celsius,

The final temperature will be 2 * 10 = 20 degrees Celsius.

In conclusion, if a piece of metal initially at 10 degrees Celsius is heated until it has twice the internal energy, its final temperature will be 20 degrees Celsius.

To know more about Celsius visit:

https://brainly.com/question/18992809

#SPJ11

Answer:

Explanation:

When the data is plotted on a graph,

the initial velocity=5-0/1-0

                             = 5ms-1

What is the final velocity at t=6⇒=60/6=10ms-1

the average acceleration=(5+7+9+11+13+15)/6 =60ms-1/6 s = 10ms-2