an airplane is flying south going 440 mph when it hits a crosswind going west at 35 mph. What is the
it velocity? (Round to the nearest mph.)
a) 405 mph southwest
b) 439 mph southwest
c) 441 mph southwest
d) 475 mph southwest

Answers

Answer 1

An airplane is flying south going 440 mph when it hits a crosswind going west at 35 mph, the resultant velocity of the airplane is approximately 439 mph southwest.

Hence, the correct option is B.

To find the resultant velocity of the airplane, we can use vector addition. The airplane's velocity in the south direction is 440 mph, and the crosswind's velocity in the west direction is 35 mph.

To find the resultant velocity, we can treat the velocities as vectors and add them together. Since the airplane is flying in the south direction and the crosswind is in the west direction, we can consider these vectors as negative in the corresponding directions.

Using the Pythagorean theorem, the magnitude of the resultant velocity can be calculated as follows

Resultant velocity = [tex]\sqrt{440^{2} }[/tex] + ([tex]-35^{2}[/tex]))

Resultant velocity = 439.66 mph

Since the resultant velocity is directed to the southwest, we can round the magnitude to the nearest mph and the direction to the nearest cardinal direction. Therefore, the resultant velocity of the airplane is approximately 439 mph southwest.

Hence, the correct option is B.

To know more about resultant velocity here

https://brainly.com/question/28864224

#SPJ4


Related Questions

A 4000 V equipotential surface is 26.0 cm farther from a positively charged particle than the 5000 V equipotential surface. What is the charge on the particle?

Answers

The charge on the positively charged particle is approximately  4.08 x 10^-6 C.

To find the charge on the particle, we can use the relationship between potential difference (V), charge (Q), and distance (r) given by the equation V = kQ/r, where k is the electrostatic constant.

Let's assume the distance between the positively charged particle and the 5000 V equipotential surface is r1 and the distance between the particle and the 4000 V equipotential surface is r2. We are given that r2 is 26.0 cm (or 0.26 m) farther than r1.

Using the equation for potential difference, we can write the following equations:

5000 = kQ/r1

4000 = kQ/r2

Dividing the two equations, we get:

5000/4000 = r2/r1

Simplifying, we find:

r2 = (5/4) * r1

Since r2 is 0.26 m farther than r1, we can write:

r2 = r1 + 0.26

Substituting the expression for r2 in terms of r1 into the above equation, we get:

r1 + 0.26 = (5/4) * r1

Simplifying, we find:

r1 = 0.52 m

Now, substituting this value of r1 into the equation 5000 = kQ/r1, we can solve for the charge Q:

Q = (5000 * r1) / k

Substituting the values of r1 and k (8.99 x 10^9 Nm²/C²), we find:

Q = (5000 * 0.52) / (8.99 x 10^9)

Q ≈ 4.08 x 10^-6 C

Therefore, the charge on the positively charged particle is approximately 4.08 x 10^-6 C.

Learn more about nature of charges :

https://brainly.com/question/13871705

#SPJ11

The potential difference between the ends of a wire is 1.5 V, and it conducts 2.5 A of current. The length of the wire is 2.0 m. What is the resistance of the wire, and what is the magnitude of the electric field in the wire?

Answers

The resistance of the wire is 0.6 ohms. The magnitude of the electric field in the wire is 0.75 V/m.

To find the resistance of the wire, we can use Ohm's Law, which states that the resistance (R) is equal to the ratio of the potential difference (V) across a conductor to the current (I) flowing through it:

R = V / I

Given that the potential difference V is 1.5 V and the current I is 2.5 A, we can calculate the resistance:

R = 1.5 V / 2.5 A = 0.6 Ω

Therefore, the resistance of the wire is 0.6 ohms.

To find the magnitude of the electric field in the wire, we can use the relationship between the electric field (E), potential difference (V), and distance (d). For a uniform electric field in a straight wire, the electric field is given by:

E = V / d

Given that the potential difference V is 1.5 V and the length of the wire (distance) d is 2.0 m, we can calculate the magnitude of the electric field:

E = 1.5 V / 2.0 m = 0.75 V/m

Therefore, the magnitude of the electric field in the wire is 0.75 V/m.

To know more about electric fields follow

https://brainly.com/question/30470913

#SPJ4

Which of the following is NOT correct for a simple magnifying glass?
a) The image is virtual.
b) The object is closer to the lens than the focal point.
c) The image is erect.
d) The lens is diverging.
e) The image is larger than the object.

Answers

The option that is NOT correct for a simple magnifying glass is:

d) The lens is diverging.

Determine what is the simple magnifying glass?

A simple magnifying glass consists of a converging lens, not a diverging lens. The purpose of a magnifying glass is to create a magnified virtual image of an object.

When an object is placed closer to the converging lens than its focal point, a virtual and erect image is formed on the opposite side of the lens.

This image appears larger than the object and is located at a distance farther away from the lens than the object itself. The converging lens bends the light rays in such a way that they appear to diverge from a point behind the lens, creating a virtual image.

Therefore, the statement that the lens is diverging is incorrect for a simple magnifying glass.

To clarify further, a diverging lens would cause the light rays to spread out, resulting in a diminished, virtual image. A converging lens, on the other hand, causes the light rays to converge, allowing for magnification and the formation of a virtual image.

To know more about magnifying, refer here:

https://brainly.com/question/32284838#

#SPJ4

what is the magnifying power of an astronomical telescope using a reflecting mirror whose radius of curvature is 5.7 m and an eyepiece whose focal length is 2.9 cm ? follow the sign conventions.

Answers

We get: Magnifying Power = -(2.85 m / 0.029 m) ≈ -98.28. The magnifying power of an astronomical telescope can be calculated using the formula: Magnifying Power = -(fo/fe), where fo is the focal length of the objective (reflecting mirror) and fe is the focal length of the eyepiece.

Given that the radius of curvature of the reflecting mirror is 5.7 m, the focal length can be determined using the relation: Focal Length = Radius of Curvature / 2. So, the focal length of the objective is 5.7 m / 2 = 2.85 m.

Converting the focal length of the eyepiece to meters, we have 2.9 cm = 0.029 m.

Substituting the values into the magnifying power formula, we get: Magnifying Power = -(2.85 m / 0.029 m) ≈ -98.28

The negative sign indicates an inverted image, and the magnitude of the magnifying power suggests that the image appears 98.28 times larger than the object.

To know more about astronomical telescope, refer here:

https://brainly.com/question/31038565#

#SPJ11

A solenoid with an iron core is 25 cm long and is wrapped with 100 turns of wire. When the current through the solenoid is 10 A, the magnetic field inside it is 2.0 T. For this current, what is the permeability of the iron? If the current is turned off and then restored to 10 A, will the magnetic field necessarily return to 2.0 T?

Answers

The permeability of the iron is approximately 1.26 x 10^(-3) Tm/A. If the current through the solenoid is turned off and then restored to 10 A, the magnetic field inside the solenoid will not necessarily return to exactly 2.0 T.

The magnetic field inside a solenoid with an iron core can be calculated using the formula:

B = μ₀ * μᵣ * (N * I) / L

Where:

B is the magnetic field (2.0 T)

μ₀ is the permeability of free space (4π x 10^(-7) Tm/A)

μᵣ is the relative permeability of iron (unknown)

N is the number of turns of wire (100)

I is the current through the solenoid (10 A)

L is the length of the solenoid (25 cm = 0.25 m)

To find the relative permeability of iron (μᵣ), we rearrange the formula:

μᵣ = (B * L) / (μ₀ * N * I)

Plugging in the given values:

μᵣ = (2.0 T * 0.25 m) / (4π x 10^(-7) Tm/A * 100 * 10 A)

   ≈ 1.26 x 10^(-3) Tm/A

Therefore, the permeability of the iron is approximately 1.26 x 10^(-3) Tm/A.

If the current through the solenoid is turned off and then restored to 10 A, the magnetic field inside the solenoid will not necessarily return to exactly 2.0 T.

The relationship between the magnetic field and the current is given by the formula mentioned earlier, and it depends on the permeability of the iron.

If the permeability changes or if there are other factors affecting the magnetic field, the value may vary.

However, if the iron remains unchanged and no other factors significantly affect the magnetic field, it is reasonable to expect that the field will return close to 2.0 T when the current is restored.

To know more about solenoid visit:

https://brainly.com/question/1873362

#SPJ11

what is a waves frequency

Answers

Answer:

the number of times the crest of a wave hits a certain point

the more waves, the higher the frequency

Explanation:

a muon is traveling at 0.996 cc . what is its momentum? (the mass of such a muon at rest in the laboratory is 207 times the electron mass.)
What is its kinetic energy?

Answers

The momentum of the muon traveling at 0.996c can be calculated using the relativistic momentum equation, and its kinetic energy is (1/0.089389 - 1) × (207 × [tex]m_e[/tex]) × c².

To calculate the momentum of a muon traveling at 0.996c, we can use the relativistic momentum equation:

p = m × v / √(1 - (v/c)²),

where p is the momentum, m is the mass, v is the velocity, and c is the speed of light.

Given that the mass of the muon at rest in the laboratory is 207 times the electron mass, we can denote the mass of the muon as m = 207 × [tex]m_e[/tex], where [tex]m_e[/tex] is the mass of an electron.

Let's substitute the values into the equation:

p = (207 × [tex]m_e[/tex]) × (0.996c) / √(1 - (0.996c/c)²)

= (207 × [tex]m_e[/tex]) × (0.996c) / √(1 - 0.996²)

= (207 × [tex]m_e[/tex]) × (0.996c) / √(1 - 0.992016)

= (207 × [tex]m_e[/tex]) × (0.996c) / √(0.007984)

= (207 × [tex]m_e[/tex]) × (0.996c) / 0.089389

Now, to calculate the kinetic energy (KE) of the muon, we can use the equation:

KE = (γ - 1) × m × c²,

where γ is the Lorentz factor given by γ = 1 / √(1 - (v/c)²).

Substituting the values:

γ = 1 / √(1 - (0.996c/c²))

= 1 / √(1 - 0.996²)

= 1 / √(1 - 0.992016)

= 1 / √(0.007984)

= 1 / 0.089389

KE = (1/0.089389 - 1) × (207 × [tex]m_e[/tex]) × c²

Learn more about kinetic energy at

https://brainly.com/question/999862

#SPJ4

A force is applied to the rim of a disk that can rotate like amerry-go-round, so as to change its angular velocity. Its initialand final angular velocities, respectively, for four situationsare: (a) -3 rad/s, 7 rad/s; (b) 3 rad/s, 7 rad/s; (c) -3 rad/s, -7rad/s; (d) 3 rad/s, -7 rad/s. Rank the situations according to thework done by the torque due to the force, greatest first (use onlythe symbols > or =, for example, a>d=b>c).

Answers

The ranking of the  work done by the torque is a > b > c > d.

What is the work done by the torque?

The work done by the torque is equal to the change in rotational kinetic energy of the body.

Mathematically, the formula for torque is given as;

τ = r.F sinθ = Iα

where;

r is the radius of the force actionF is the applied forceI is the moment of inertiaα is the angular acceleration

The formula for angular acceleration is given as;

α = Δω / Δt

where;

Δω is the change in angular speedΔt is the change in time of motion

Thus, the greater the change in angular speed, the greater the work done by the applied torque.

(a) Δω = 7 rad/s - (-3 rad/s) = 10 rad/s

(b) Δω = 7 rad/s - 3 rad/s = 4 rad/s

(c) Δω = -7 rad/s - (-3 rad/s) = -4 rad/s

(d) Δω = -7 rad/s - 3 rad/s =  -10 rad/s

The ranking, a > b > c > d

Learn more about work done here: https://brainly.com/question/8119756

#SPJ4

Which of the following statements about zoroastrianism is false?
A. The people of Persia were allowed to freely accept it or not accept it; itwas not imposed upon them
B. Both Ahurda Mazda, and Angra Mainyu are considered gods
C. It was characterized by the Great Creator and the Destructive Forces
D. It was named after its founder Zoroaster

Answers

The false statement about Zoroastrianism is both Ahurda Mazda and Angra Mainyu are considered gods. In Zoroastrianism, Ahura Mazda is considered the supreme deity and the embodiment of good, while Angra Mainyu (also known as Ahriman) represents the embodiment of evil and is not considered a god.

Zoroastrianism is an ancient Iranian religion founded by the prophet Zoroaster (or Zarathustra). It originated in Persia (modern-day Iran) and played a significant role in the development of Persian culture and civilization. Zoroastrianism promotes the belief in the existence of one supreme deity, Ahura Mazda, who represents goodness, truth, and light. The religion also recognizes the presence of destructive forces, personified by Angra Mainyu, representing evil and darkness. Zoroastrianism emphasizes the eternal struggle between these opposing forces and the importance of choosing good over evil. The faith does not impose itself on individuals but allows people to freely accept or reject its teachings.

To know more about zoroastrianism, click here https://brainly.com/question/8148348

#SPJ11

A series RLC circuit consists of a 100 Ω resistor, 0.15 H inductor, and a 30μF capacitor. It is attached to a 120V/60 Hz power line. Calculate: (a) the emf Srms (b) the phase angle φ, (c) the average power loss.

Answers

(a) The rms voltage is 120 V, and the frequency of the power line is 60 Hz. The circuit's impedance is calculated to be 100.075 Ω by combining the inductive and capacitive reactances.(b) tanφ = XL - XC /R where XL is the inductive reactance, XC is the capacitive reactance, and R is the resistance.(c) The average power loss is determined by calculating the average power absorbed by the resistor. By using the formula Pavg = ½Irms²R, the average power loss can be determined.

(a) The emf Srms = 120 V and the frequency of the power line is 60 Hz, the impedance of the circuit is calculated as 100.075 Ω, by combining the inductive and capacitive reactances.(b) The phase angle φ = tan^-1((XL - XC)/R) where XL is the inductive reactance, XC is the capacitive reactance, and R is the resistance.(c) The average power loss can be calculated using the formula Pavg = ½Irms²R, where Irms is the current through the resistor, R is the resistance of the circuit. Thus, the average power loss can be found by substituting the values of the variables, i.e., Pavg = ½ (Vrms / Z)^2 × R where Vrms is the rms voltage and Z is the impedance.

Know more about rms voltage, here:

https://brainly.com/question/13507291

#SPJ11

I will mark you brainlist!

What mythical creature do you think is possibly real, and not actually a myth? Why?

Examples of mythical creatures: Mermaids/Merman, Fairies/ Pixie, Nymphs, Dragons, Unicorn, Leprechauns, Werewolf, Loch Ness Monster, Sphinx, Centaur, Griffin, Yeti, Pegasus, Basilisk, Chimera, Ghoul, Imp, Gnome, Manticore, Troll, Bigfoot, Phoenix, Vampire etc.

You can choose one that is listed or not listed.

Answers

Explanation:

With most of our blue planet covered by water, it's little wonder that, centuries ago, the oceans were believed to hide mysterious creatures including sea serpents and mermaids. Merfolk (mermaids and mermen) are, of course, the marine version of half-human, half-animal legends that have captured human imagination for ages. One source, the "Arabian Nights," described mermaids as having "moon faces and hair like a woman's but their hands and feet were in their bellies and they had tails like fishes."

C.J.S. Thompson, a former curator at the Royal College of Surgeons of England, notes in his book "The Mystery and Lore of Monsters" that "Traditions concerning creatures half-human and half-fish in form have existed for thousands of years, and the Babylonian deity Era or Oannes, the Fish-god ... is usually depicted as having a bearded head with a crown and a body like a man, but from the waist downwards he has the shape of a fish." Greek mythology contains stories of the god Triton, the merman messenger of the sea, and several modern religions including Hinduism and Candomble (an Afro-Brazilian belief) worship mermaid goddesses to this day.

A 7.7 mW laser produces a narrow beam of light. How much energy is contained in a 1.0 m length of its beam? Please show step by step

Answers

The energy contained in a 1.0 m length of the beam from a 7.7 mW laser is 7.7 μJ (microjoules).

To calculate the energy contained in the length of the laser beam, we need to use the power of the laser and the formula:

Energy = Power × Time

However, we don't have the time information here. To proceed, we'll assume a continuous wave laser where the power remains constant over time.

Given:

Power of the laser = 7.7 mW (milliwatts)

Length of the beam = 1.0 m

First, we need to convert the power from milliwatts to watts:

7.7 mW = 7.7 × 10^(-3) W

Next, we can calculate the energy using the formula:

Energy = Power × Time

Since we assume a continuous wave laser, we can rearrange the formula as:

Energy = Power × Time = Power × (1 second)

Plugging in the values:

Energy = (7.7 × 10^(-3) W) × (1 second)

The time in this case is 1 second because we assume a continuous beam over that duration. Multiplying the power by 1 second doesn't change the value.

Finally, we can calculate the energy:

Energy = (7.7 × 10^(-3) W) × (1 second)

= 7.7 × 10^(-3) J (joules)

Since the joule is a relatively large unit, it's common to express small energy values in smaller units such as microjoules (μJ).

Converting from joules to microjoules:

1 J = 10^6 μJ

Therefore,

Energy = 7.7 × 10^(-3) J

= 7.7 × 10^(-3) × 10^6 μJ

= 7.7 × 10^(3) μJ

= 7.7 μJ

The energy contained in a 1.0 m length of the beam from a 7.7 mW laser is 7.7 μJ (microjoules).

To learn more about energy, visit    

https://brainly.com/question/2003548

#SPJ11

a binary phase diagram indicates the phases of two elements (at least one of which is metallic) as a function of composition and temperature at atmospheric pressure? (a) true (b) false

Answers

The given statement '' A binary phase diagram indicates the phases of two elements (at least one of which is metallic) as a function of composition and temperature at atmospheric pressure '' is True.

A binary phase diagram is a graphical representation that shows the phases of two elements, at least one of which is metallic, as a function of composition and temperature at a specific pressure, typically atmospheric pressure.

The diagram displays different regions representing the stability of different phases (such as solid, liquid, and gas) as the composition and temperature of the system are varied. It is a valuable tool in understanding the behavior and phase transitions in binary systems.

Hence, The given statement '' A binary phase diagram indicates the phases of two elements (at least one of which is metallic) as a function of composition and temperature at atmospheric pressure '' is True.

To know more about binary phase diagram here

https://brainly.com/question/31949917

#SPJ4

determine the pressure drop per 100-m length of horizontal new 0.35-m-diameter cast iron water pipe when the average velocity is 2.9 m/s.

Answers

When the average velocity is 2.4 m/s, the horizontal 0.35 meter diameter cast iron water pipe experiences a pressure drop (P) of roughly 16457.14 kPa every 100 meters.

To determine the pressure drop per 100-meter length of a horizontal 0.35-meter diameter cast iron water pipe, we can use the Darcy-Weisbach equation. The equation is as follows:

[tex]\begin{equation}\Delta P = \frac{f \cdot \frac{L}{D} \cdot (\rho \cdot V^2)}{2}[/tex]

where ΔP is the pressure drop, f is the Darcy friction factor, L is the length of the pipe (100 meters in this case), D is the diameter of the pipe (0.35 meters), ρ is the density of water, and V is the average velocity of water.

To calculate the pressure drop, we need to determine the Darcy friction factor. For a rough cast iron pipe, we can estimate the friction factor to be around 0.02.

Using the given values and the estimated friction factor, the calculation becomes:

[tex]\begin{equation}\Delta P = \frac{0.02 \cdot \frac{100}{0.35} \cdot (\rho \cdot 2.4^2)}{2}[/tex]

Since the density of water (ρ) is approximately 1000 kg/m³, we can substitute this value and calculate the pressure drop:

ΔP = [tex]\frac{0.02 \times \frac{100}{0.35} \times 1000 \times 2.4^2}{2}[/tex]

Let's solve the expression to calculate the pressure drop (ΔP) in kilopascals (kPa):

ΔP =  [tex]\frac{0.02 \times \frac{100}{0.35} \times 1000 \times 2.4^2}{2}[/tex]

First, let's simplify the expression:

ΔP = [tex]\frac{0.02 \times (285.714) \times (1000 \times 5.76)}{2}[/tex]

   = 16457.14

Therefore, the pressure drop (ΔP) per 100-meter length of the horizontal 0.35-meter diameter cast iron water pipe, when the average velocity is 2.4 m/s, is approximately 16457.14 kPa.

To know more about the cast iron water pipe refer here :

https://brainly.com/question/32455854#

#SPJ11

Complete question :

Determine the pressure drop per 100 -m length of horizontal new 0.35−m-diameter cast iron water pipe when the average velocity 2.4 m/s. Δp= kPa

In an L-R-C series circuit, the resistance is 500 ohms, the inductance is 0.380 henrys, and the capacitance is 2.00×10−2 microfarads.
Part A
What is the resonance angular frequency ω0 of the circuit?
Express your answer in radians per second to three significant figures.
Part B
The capacitor can withstand a peak voltage of 570 volts. If the voltage source operates at the resonance frequency, what maximum voltage amplitude Vmax can the source have if the maximum capacitor voltage is not exceeded?
Express your answer in volts to three significant figures.

Answers

The resonance angular frequency (ω0) of the circuit is approximately 3615 radians per second. The maximum voltage amplitude (Vmax) that the source can have without exceeding the maximum capacitor voltage is 570 volts.

Part A:

The resonance angular frequency ω0 of the circuit can be calculated using the formula:

ω0 = 1 / √(LC)

Inductance (L) = 0.380 H

Capacitance (C) = 2.00×10^(-2) μF = 2.00×10^(-8) F

Converting the capacitance to farads:

C = 2.00×10^(-8) F

Plugging the values into the formula, we get:

ω0 = 1 / √(0.380 * 2.00×10^(-8))

   = 1 / √(7.6×10^(-9))

   = 1 / (2.76×10^(-4))

   ≈ 3615 rad/s

Therefore, the resonance angular frequency ω0 of the circuit is approximately 3615 radians per second.

Part B:

To determine the maximum voltage amplitude Vmax that the source can have without exceeding the maximum capacitor voltage, we need to consider the relationship between the voltage across the capacitor (Vc) and the voltage across the source (Vs) in an L-R-C series circuit.

At resonance, the voltage across the capacitor (Vc) is maximum, and the voltage across the inductor (VL) and resistor (VR) is minimum.

In this case, the maximum voltage across the capacitor is equal to the maximum voltage across the source.

Peak voltage withstand by the capacitor = 570 V

Therefore, the maximum voltage amplitude (Vmax) that the source can have without exceeding the maximum capacitor voltage is 570 V.

To know more about capacitor visit:

https://brainly.com/question/21851402

#SPJ11

) A 1.0kW kettle contains 500g of boiling waterCalculate the time needed to evaporate all the water
in the kettle (specific latent heat of vaporization2.26 MJ kg​-1

Answers

Answer:

t = 1130 s = 18.83 min

Explanation:

First, we will calculate the energy required to evaporate 500 g of water:

[tex]E = mL[/tex]

where,

E = Energy Required for evaporation of water =?

m = mass of water = 500 g = 0.5 kg

L = Latent heat of vaporization of water = 2.26 MJ/kg = 2260 KJ/kg

Therefore,

[tex]E = (0.5\ kg)(2260\ KJ/kg)\\E = 1130\ KJ[/tex]

Now, we will calculate the time required:

[tex]P = \frac{W}{t}\\\\t = \frac{W}{P}[/tex]

where,

t = time = ?

P = Power of kettle = 1 KW

Therefore,

[tex]t = \frac{1130\ KJ}{1 KW}\\\\[/tex]

t = 1130 s = 18.83 min

Students push a swing with a hard push and a soft push. Each time the students count how many time the swing moves back and forth before stopping. What variable is tested in this investigation?
a. differences in pushes and pulls
b. force of the push
c. number of time the swing moves
d. distance the swing moves

Answers

answer: c. number of time the swing moves.
evidence: “the students count how many times the swing move back and forth before stopping”

a piece of 14-gauge copper wire (meaning that it has a diameter of 1.63mm) has a resistance of 0.128 . the resistivity of copper is . what must be the length of the wire?

Answers

The length of the copper wire must be approximately 44.2 meters for it to have a resistance of 0.128 ohms, assuming a 14-gauge wire with a diameter of 1.63 mm and using the resistivity of copper.

To find the length of the wire, we can use Ohm's Law, which states that the resistance (R) is equal to the product of the resistivity (ρ), the length (L), and the cross-sectional area (A) of the wire, divided by the diameter (d) of the wire squared.

The formula can be written as:

R = ρ * (L / A)

Resistance (R) = 0.128 ohms

Resistivity of copper (ρ) = (1.68 × 10^-8) ohm-meter (at 20°C)

Diameter (d) = 1.63 mm = 0.00163 meters (converted from millimeters to meters)

We need to find the length (L) of the wire.

To calculate the cross-sectional area (A) of the wire, we can use the formula for the area of a circle:

A = π * (d/2)^2

Plugging in the values, we have:

A = 3.14159 * (0.00163 / 2)^2

A  ≈ 2.08 x 10^-6 square meters

Rearranging Ohm's Law to solve for the length (L), we get:

L = (R * A) / ρ

Substituting the given values:

L = (0.128 * 2.08 x 10^-6) / (1.68 x 10^-8)

L  ≈ 44.2 meters

The length of the copper wire must be approximately 44.2 meters for it to have a resistance of 0.128 ohms, assuming a 14-gauge wire with a diameter of 1.63 mm and using the resistivity of copper.

To know more about resistivity visit:

https://brainly.com/question/13735984

#SPJ11

6)which types of telescopes will be able to detect flux from objects if the telescopes are located on earth? use figure 5.6 for guidance. bold the correct answers.

Answers

The types of telescopes that will be able to detect flux from objects when located on Earth include optical telescopes, radio telescopes, and infrared telescopes.

Optical Telescopes: Optical telescopes are specifically designed to gather and focus visible light, enabling the detection of flux from astronomical objects. They come in two main types: refracting telescopes, which use lenses to gather and focus light, and reflecting telescopes, which use mirrors to capture and direct light to a detector or eyepiece.

Radio Telescopes: Radio telescopes detect and analyze radio waves emitted by astronomical objects. They are designed to capture a wide range of radio frequencies and are crucial for studying celestial sources that emit primarily in the radio part of the electromagnetic spectrum. By analyzing the received signals, astronomers can study phenomena such as pulsars, quasars, and cosmic microwave background radiation.

To learn more about telescopes, Click here:

https://brainly.com/question/31169822

#SPJ11

A lens produces a real imag eof a real object.
If lens 1 from part d were placed in exactly the same location as lens 2, would the image produced by lens 1 be larger or smaller than the image produced by lens 2?

Answers

If lens 1 from part d were placed in exactly the same location as lens 2, the image produced by lens 1 would be larger than the image produced by lens 2.

The reason is that the magnification produced by a lens depends on the ratio of the image distance to the object distance.

The larger the ratio, the larger the magnification.

Therefore, if lens 1 were placed in the same location as lens 2, it would produce a larger image because lens 1 has a shorter focal length and will bring the image closer to the lens than lens 2.

This will result in a larger image than that produced by lens 2.

Learn more about the lens:

brainly.com/question/28039799

#SPJ11

A longitudinal wave is observed. Exactly 6 crests are observed
to move past a given point in 9.1 s. Its wavelength is 2.4 m and
its frequency is 0.66 HZ. What is the speed of the wave?

Answers

The speed of the wave is 1.58 meters per second (or 1.584 if you don’t round it).
You multiply wavelength by frequency to get the speed of a wave.
2.4 times 0.66 = 1.548 meters per second.

If you didn’t have the frequency before hand, you would just divide the 6 crests by the 9.1 seconds.

a 17.0-n force stretches a wire 0.650 cm. (a) what force will stretch a similar piece of wire 1.87 cm? (b) a force of 21.3 n is applied to a similar piece of wire. how far will it stretch?

Answers

(a) To find the force that will stretch a similar piece of wire to 1.87 cm, we can use the concept of Hooke's Law. Hooke's Law states that the force required to stretch or compress a spring (or wire) is directly proportional to the displacement or change in length.

Given that the original force is 17.0 N and it stretches the wire by 0.650 cm, we can set up a proportion to find the force required for a 1.87 cm stretch.

Let F1 be the original force, x1 be the original displacement, F2 be the unknown force, and x2 be the desired displacement. The proportion can be expressed as:

F1 / x1 = F2 / x2

Substituting the given values, we have:

17.0 N / 0.650 cm = F2 / 1.87 cm

Now we can solve for F2:

F2 = (17.0 N / 0.650 cm) * 1.87 cm

F2 ≈ 48.8 N

Therefore, a force of approximately 48.8 N will stretch a similar piece of wire to 1.87 cm.

(b) To determine how far a similar piece of wire will stretch when a force of 21.3 N is applied, we can use Hooke's Law again.

Using the same variables as before, the proportion can be set up as:

F1 / x1 = F2 / x2

Substituting the given values:

17.0 N / 0.650 cm = 21.3 N / x2

Solving for x2:

x2 = (21.3 N / 17.0 N) * 0.650 cm

x2 ≈ 0.815 cm

Therefore, a force of 21.3 N will cause the wire to stretch approximately 0.815 cm.

To know more about force visit :

https://brainly.com/question/12785175

#SPJ11

Is your increase in gravitational potential energy the same in both cases? When Climbing a mountain on a zigzag path and on a straight path

Answers

Answer:

The increase in gravitational potential energy is the same in both cases

Explanation:

It is easier to climb a mountain in a zigzag way rather than climbing on a straight line but since the distance is the same ( vertical height ) , mass and gravity is the same. Hence the increase in gravitational potential energy is the same in both cases.

gravitational potential energy = mgh ( same in both cases )

m = mass

g = acceleration due to gravity

h = distance ( vertical height )

It would not be economical to connect the houses to the National Grid.Give one reason why.

Answers

Why is it not economical to connect houses to the national grid?
Why does it cost so much? Electricity is sent through the National Grid cables at very high voltages - between 132,000 and 400,000. It benefits National Grid to not have to keep investing in reinforcing the high-voltage grid necessary to transport the power long distances

A luminous object moves along the optical axis of a concave spherical mirror. If the object approaches the mirror and its focal point, where does the image of the object move? a. It moves perpendicular to the optical axis b. Towards the mirror c. Away from the mirror d. It does not move at all

Answers

The image of the object moves towards the mirror as the object approaches the mirror and its focal point.

When an object moves along the optical axis of a concave spherical mirror and approaches the mirror's focal point, the image formed by the mirror undergoes a change in position. This change is characterized by the image moving towards the mirror.

In a concave mirror, the focal point is located on the same side as the object, but at a distance determined by the mirror's curvature. As the object moves closer to the focal point, the reflected rays converge and the image position changes. The image moves towards the mirror as a result.

To understand this phenomenon, we can consider the ray diagram for a concave mirror. As the object approaches the focal point, the rays of light from different points on the object converge towards the focal point after reflection. This convergence leads to the image moving towards the mirror.

When a luminous object moves along the optical axis of a concave spherical mirror and approaches the mirror's focal point, the image of the object moves towards the mirror. This is due to the convergence of reflected rays as the object approaches the focal point, resulting in a change in the image position.

To know more about Concave spherical mirror visit:

https://brainly.com/question/31951940

#SPJ11

What happens to a digital signal sent using electromagnetic waves as it travels farther from its source?
A. The signal becomes weaker and more difficult to detect
B. The signal slows down and becomes distorted
C. The signal needs to be amplified before it can be detected
D. The digital signal changes to an analog signal.​

Answers

Answer:

did you find the answer please answer back

Answer:a

Explanation:ap ex verified

An object's inertia is its tendency to maintain contact:

1.) Mass.
2.) Position.
3.) Acceleration.
4.) Velocity.

Answers

hello! it is velocity.

i say this because, Inertia is the tendency of an object to resist changes in its state of motion. ... The state of motion of an object is defined by its velocity - the speed with a direction.

In Gay-Lussac's law, the pressure of a gas increases due to an increase in temperature because _____.
(a) the molecules strike the walls of the container less often.
(b) the molecules strike the walls of the container more often.
(c) the molecules get bigger.
(d) there is a decrease in the volume of the container.
(e) there is an increase in the number of gas particles.

Answers

Option (b) is the correct answer: the pressure of a gas increases due to an increase in temperature because the molecules strike the walls of the container more often.

Gay-Lussac's law, also known as the pressure law, states that the pressure of a gas is directly proportional to its temperature, assuming the volume and amount of gas remain constant. Therefore, an increase in temperature leads to an increase in pressure. The explanation for this phenomenon lies in the kinetic theory of gases.

According to the kinetic theory, the temperature of a gas is related to the average kinetic energy of its molecules. When the temperature increases, the average kinetic energy of the gas molecules also increases. As a result, the gas molecules move with higher velocities and collide more frequently with the walls of the container.

The frequency of molecular collisions with the container walls is directly related to the pressure exerted by the gas. When the gas molecules strike the walls more often due to increased kinetic energy, the pressure exerted by the gas increases.

Therefore, option (b) is the correct answer: the pressure of a gas increases due to an increase in temperature because the molecules strike the walls of the container more often.

An increase in temperature causes the pressure of a gas to increase because the gas molecules collide more frequently with the walls of the container, as explained by Gay-Lussac's law and the kinetic theory of gases.

To know more about molecules visit:

https://brainly.com/question/1078183

#SPJ11

describe atmospheric pressure and water pressure​

Answers

Answer:

The difference is that water is an incompressible fluid — its density is almost constant as the pressure changes — while air is a compressible fluid — its density changes with pressure. ... Atmospheric pressure is the pressure exerted on a surface by the weight of the atmosphere (a compressible fluid) above it

Explanation:

change some words

Imagine carefully weighing a metal can, leaving it out in the rain for weeks and weeks
until it was very rusted, and then carefully weighing it again. Would the can be heavier or lighter after it was rusted? Why?

Answers

Answer:

The can would be heavier.

Explanation:

The more rust is on the can, (Or object) the more it weights it down.

Answer:

The answer would be heavier, though it depends upon the type of metal. Rusting is essentially corrosion. Rust is often caused by a piece of metal getting soaked in water and then being exposed to oxygen. The rust will add more weight to the can so it becomes heavier.

Other Questions
Count the number of strings of decimal digits of length 6 with the following proper-ties.a) all even digitsb) begin and end with the same digitc) contains at least one 0d) contains exactly three 7se) contains exactly two 3s or exactly three 4s Morales, president of Tradewind Industries, Inc., would have actual implied authority to:a. issue corporate stock.b. remove a vice-president of the company from office.c. bind the company in a sale in the ordinary course of the company business.d. set the amount for production bonuses of the other officers. Find the Maclaurin series for the function -czby using partial fractions or otherwise. Output (Q): 0 1 2 3 4 5 6Total Cost (TC): $24 $33 $41 $48 $54 $61 $69Refer to the table shown here. Diminishing marginal returns starts to occur between units:2 and 3.3 and 4.4 and 5.5 and 6. The probability of drawing a bluemarble from a bag containingthese marbles is 1/2.If you replace the marble each time,predict how many times a blue marblewill be chosen out of 50 draws Let k, h be unknown constants and consider the linear system: + 5% = 6y 7 T - -31 = 4 z + 7 y -3 -9z+10y + hz = k This system has a unique solution whenever h If he is the (correct) value entered above, then the above system will be consistent for how many value(s) of k? Question 1 1 pts What was one detrimental effect caused by chain stores according to anti-chain store activists in the 1920s? Edit View Insert Format Tools Table 12pt Paragraph BIU TV: 0 words starting with cyclohexene, propose a reasonable synthesis of the cyclohexene derivative. a toy car is placed 13.0 cm from a convex mirror. the image of the car is upright and one-sixth as large as the actual car. calculate the mirror's power in diopters. On January 1, 2021 the national government provided a grant to Brgy ACYFA2 amounting to 24,000,000 intended to construct a new barangay hall provided that the said construction was finihsed August 15, 2021 for an amount of P32,000,000 with best estimate of the useful life at 40 yearsOn December 31, 2022 how much should be the ending balance of the recorded contra asset against the building barangay hall The most beautiful things in the world cannot be seen or touched, they are felt with the heart" means 1. Besides the fact that the customers have different ways to buy products, what are the major advantages of this kind of omni-channel strategy? 2. Evaluate the opportunities and risks involved when a formerly pure e-commerce company like Zalando opens a brick-and-mortar store. 3. In view of the recent Coronavirus pandemic, how do you think a) brick-and-mortar retailers and b) purely e-tailers (like Amazon) have altered their operational strategy? what is significant about the last lines of the chapter? what idea is lost or ""incommunicable forever""? the nurse provides care for a client diagnosed with asthma. The client has a prescription for albuterol and beclomethasone metered-dose inhalers. Which client action indicates to the nurse that further teaching is needed? (Select all that apply.)1. Using a spacer with both inhalers.2. Rinsing the mouth after taking the beclomethasone metered-dose inhaler.3. Writing down how many doses have been taken from the metered-dose inhalers.4. Using the beclomethasone inhaler, waiting 5 minutes, then taking the albuterol inhaler.5. Avoiding the use of a spacer to prevent bronchospasm. If a 90% confidence interval for the difference of means 1 2 contains all negative values, what can we conclude about the relationship between 1 and 2 at the 90% confidence level?We can conclude that 1 = 2.We can conclude that 1 > 2.We can not make any conclusions.We can conclude that 1 < 2. According to its blackbody curve, the sun puts out most of its light as what color? A kayaker needs to paddle north across a 100-m-wide harbor. The tide is going out, creating a tidal current that flows to the east at 2.0 m/s. The kayaker can paddle with a speed of 3.0 m/s. In which direction should he paddle in order to travel straight across the harbor? by considering different paths of approach, show that the function below has no limit as (x,y)->(0,0) h(x,y)=(x^2+y)/y 1) Examine the of h along curves that end at (0,0). Along which set of curves is h a constant value? 2) if (x,y) approaches (0,0) along the curve when k=2 used in the set of curves found above, what is the limit? the term shophet (""judge"") is closely related to the hebrew term for ________. A nurse is preparing to administer a second infusion of trastuzumab [Herceptin] to a patient who has breast cancer. The patient tells the nurse that she experienced chills, fever, pain, and nausea after her first infusion. What will the nurse do?a. Contact the provider to request a CBC to assess for neutropenia.b. Ensure that oxygen and respiratory support measures are readily available.c. Reassure the patient that these symptoms will diminish with each infusion.d. Request an order for an electrocardiogram.