Explain, step by step, how to calculate the amount of current (I) that will go through the resistor in this circuit

Answer:

the number of turns in the primary coil is 13000

Explanation:

Given the data in the question;

V₁ = 13000 V

V₂ = 120 V

N₁ = ?

N₂ = 120 turns

the relation between the voltages and the number of turns in the primary and secondary coils can be expressed as;

V₁/V₂ = N₁/N₂

V₁N₂ = V₂N₁

N₁ = V₁N₂ / V₂

so we substitute

N₁ = (13000 V × 120 turns) / 120 V

N₁ = 1560000 V-turns / 120 V

N₁ = 13000 turns

Therefore, the number of turns in the primary coil is 13000

Correct question is;

A 4-foot spring measures 8 feet long after a mass weighing 8 pounds is attached to it. The medium through which the mass moves offers a damping force numerically equal to √2 times the instantaneous velocity. Find the equation of motion if the mass is initially released from the equilibrium position with a downward velocity of 7 ft/s. (Use g = 32 ft/s²)

Answer:

x(t) = 7te^(-2t√2)

Explanation:

We are given;

Weight; W = 8 lbs

mass; m = W/g

g = 32 ft/s²

Thus;

m = 8/32

m = ¼ slugs

From Newton's second law we can write the equation as;

m(d²x/dt²) = -kx - β(dx/dt)

Rearranging this, we have;

(d²x/dt²) + (β/m)(dx/dt) + (k/m)x = 0

Where;

β is damping constant = √2

k is spring constant = W/s

Where s = 8ft - 4ft = 4ft

k = 8/4

k = 2

Thus,we now have;

(d²x/dt²) + (√2/(¼))(dx/dt) + (2/(¼))x = 0

>> (d²x/dt²) + (4√2)dx/dt + 8x = 0

The auxiliary equation of this is;

m² + (4√2)m + 8 = 0

Using quadratic formula, we have;

m1 = m2 = -2√2

The general solution will be gotten from;

x_t = c1•e^(mt) + c2•t•e^(mt)

Plugging in the relevant values gives;

x_t = c1•e^(mt) + c2•t•e^(mt)

At initial condition of t = 0, x_t = 0 and thus; c1 = 0

Also at initial condition of t = 0, x'(0) = 7 and thus;

Since c1 = 0, then c2 = 7

Thus,equation of motion is;

x(t) = 7te^(-2t√2)

Answer:

Light is being absorbed

Hope this helps!

Light is being absorbed

The quarterback is getting hit with a force of 100 Newtons.

We can use Newton's second law of motion:

Force = Mass * Acceleration

Given that the mass of the defensive lineman is 100 kg and the acceleration is 1 m/s², we can substitute these values into the equation:

Force = 100 kg * 1 m/s²

Force = 100 N

Therefore, the quarterback is getting hit with a force of 100 Newtons.

Learn more about  Newton's second law here : brainly.com/question/1121817

#SPJ1

Answer:

isopropyl alcohol would form smaller droplets, because it has lower surface tension than water has

Explanation:

Ap3x

The droplets made of isopropyl alcohol instead of water be smaller due to surface tension.

The single drop of a liquid in the form of sphere is called droplet.

Water can form large dewdrops in nature. Isopropyl alcohol would form smaller droplets, because it has lower surface tension than water.

Surface tension is the property of the liquid to acquire minimum surface area.

Thus, droplets made of isopropyl alcohol instead of water be smaller.

Learn more about droplet.

https://brainly.com/question/2926487

#SPJ2

Answer:

the wave represents the second harmonic.

Explanation:

Given;

length of the cord, L = 64 cm

The first harmonic of a cord fixed at both ends is given as;

[tex]f_o = \frac{V}{2L}[/tex]

The wavelength of a standing wave with two antinodes is calculated as follows;

L = N---> A -----> N    +   N ----> A -----> N

Where;

N is node

A is antinode

L = N---> A -----> N    +   N ----> A -----> N =  λ/2  + λ/2

L = λ

The harmonic is calculated as;

[tex]f = \frac{V}{\lambda} \\\\f = \frac{V}{L} = 2(\frac{V}{2L} ) = 2(f_o) = 2^{nd} \ harmonic[/tex]

Therefore, the wave represents the second harmonic.

L = λ

Answer:

Change in KE = +1.96×10^4 J while the change in ME = 0 J

Answer:

150 J

Explanation:

If there is not any dissipative force in the system, the mass and the spring will oscillate eternally., but of course, we assume this is a theoretical situation. The conservation of energy in a system implies that the sum of the potential energy plus kinetic energy remains constant, therefore if in the initial point the mass has 200 J (potential energy) and is at rest ( kinetic energy = 0) the overall energy at the beginning is 200 J. At any point of the oscillation if the potential energy is 50 J the kinetic energy must be 150 J.

Answer:

C. Constant

Explanation:

The total energy of the cannonball remains constant as it travels through the air.

Answer:

Explanation:

hi my name is Ava

In the CrystPX Technology process, suspension crystallization of paraxylene (PX) in the xylene isomer mixture is used to produce paraxylene crystals.  At the back end of the process, high paraxylene recovery is obtained by operating the crystallizers at colder temperatures.

Paraxylene crystals are created using the CrystPX Technology by suspending paraxylene (PX) in a mixture of xylene isomers. High paraxylene recovery is achieved at the end of the process by running the crystallizers at lower temperatures.

The paraxylene technology from BP, a novel method using single stage crystallization for paraxylene (pX) recovery, is licensed exclusively to Lummus Technology for use around the world.

This cutting-edge architecture makes the Lummus Technology/BP pX crystallization technology the most energy-efficient paraxylene recovery process, together with excellent feed impurity tolerance and low total unit fuel consumption.

The Lummus Technology/BP paraxylene process has a high degree of dependability, is inexpensive, and can take a variety of feed compositions.

Therefore, With the aid of isomerization over a non-noble metal catalyst, the yield of xylene is improved even further. Optimized fractionation lowers reboiler duty, resulting in less energy use and emissions.

Learn more about crystallizer here:

https://brainly.com/question/20725934

#SPJ2

A solution is a homogeneous mixture, which may be liquid, gas or solid, formed by dissolving one or more substances.

According to this question, a salt dissolved in water is an example of solution because it involves a solute and a solvent.

The rate of a chemical reaction can be decreased by reducing the concentration of the reactants so as not to provoke a reaction.

In a chemical reaction, the particles of the reactants must collide to initiate the reaction.

Learn more about solution at: https://brainly.com/question/1616939

#SPJ1

Answer:

5,000-10,000 K

Explanation:

make me your brainlist pls

Answer:

all of the above.

Explanation:

all of these qualities are crucial in order to have a successful business.

Answer:

The main reason is that very young calves are more noticeable to predators when mixed with older calves from the previous year

Explanation:

They are forced to migrate by carnivores that hunt them.

Explanation:

F1 will have to have  65 N vertical up force to balance the net 65 N down on the body  AND it will have to have  70 N horizontal to the right to balance the 70 N force that is acting to the left

Magnitude = sqrt ( 65^2 + 70^2) = 95.5  N

Answer:

taking in oxygen and giving out carbon dioxide is called respiration

Answer:

i think that respiratiln is when you breqth

Answer:

6.96ms/2 or 7ms/2

Explanation:

v2=u2 +2as second equation of motion

u=o

v=35

S=88

a=?

35^2=0^2 +2xax88

=1225 =0+176a

1225=176a

1224/176=6.96ms/2 or 7ms/2

Answer:

the total magnetic force on the 2 sides of the wire is 0.30 N

Option a) 0.30 N is the correct answer

Explanation:

Given the data in the question;

both the sides of the right angled triangle is the same and the magnetic is in the plane of the  triangle and is perpendicular to the hypotenuse.

hence, angle between the magnetic field and both the sides of the triangle is 45 degrees.

∅ = 45°

I = 2.0 A

L = 15 cm = 0.15 m

B = 0.7 T

Total magnetic force on the 2 sides of the wire will be;

F = 2BILsin∅

we substitute

F = 2 × 0.7 × 2.0 × 0.15 × sin(45°)

F = 0.42 × 0.70710678

F = 0.2970 ≈ 0.30 N

Therefore, the total magnetic force on the 2 sides of the wire is 0.30 N

Option a) 0.30 N is the correct answer

Answer:

work done by friction = 5889 J

Explanation:

We are given;

Mass of car; m = 130 kg

Speed at point A; v1 = 25 m/s

Speed at point B: v2 = 8 m/s

Since radius is 12 m

At point A, distance is; y1 = 12 m

At point B, distance is; y2 = -12 m

Now, formula for work done by all the forces is given by the equation;

Total work;

W_gravity + W_others = K2 - K1

Where W_others is work done by other forces which is equal to work done by friction

Where K2 - K1 is change in kinetic energy.

W_grav is also change in potential energy and is expressed as;

W_grav = mgy1 - mgy2

K2 - K1 = ½m(v1)² - ½m(v2)²

Thus;

mgy1 - mgy2 + W_others = ½m(v1)² - ½m(v2)²

Making W_others the subject;

W_others = ½m(v1)² - ½m(v2)² + mgy2 - mgy1

Plugging in the relevant values;

W_others = (½ × 130 × 25²) - (½ × 130 × 8²) + (130 × 9.8 × -12) - (130 × 9.8 × 12)

W_others = 5889 J

Recall that I earlier said W_others = work done by friction.

Thus, work done by friction = 5889 J

Answer:

a. 660 gallons

b.665 gallons

c. 1,800

There is more to the Earth than what we can see on the surface. In fact, if you were able to hold the Earth in your hand and slice it in half, you'd see that it has multiple layers. But of course, the interior of our world continues to hold some mysteries for us. Even as we intrepidly explore other worlds and deploy satellites into orbit, the inner recesses of our planet remains off limit from us.

However, advances in seismology have allowed us to learn a great deal about the Earth and the many layers that make it up. Each layer has its own properties, composition, and characteristics that affects many of the key processes of our planet. They are, in order from the exterior to the interior – the crust, the mantle, the outer core, and the inner core. Let's take a look at them and see what they have going on.

Like all terrestrial planets, the Earth's interior is differentiated. This means that its internal structure consists of layers, arranged like the skin of an onion. Peel back one, and you find another, distinguished from the last by its chemical and geological properties, as well as vast differences in temperature and pressure.

Explanation:

Answer:

D. The Light Is Refracted

Explanation:

<3

In general, option c - warming it up on the stove - is often an effective method to increase the reaction rate.

Increasing the temperature of a reaction generally leads to faster reaction rates. This is because higher temperatures provide more thermal energy to the reactant particles, causing them to move faster and collide more frequently. The increased collision frequency and energy lead to more successful collisions and a higher likelihood of effective molecular interactions, which speeds up the reaction. On the other hand, options a and b - putting it in the fridge where it is cold or covering it with a blanket to make it dark - are unlikely to have a significant effect on the reaction rate. While temperature can influence reaction rates, cooling the reaction or making it dark typically reduces the kinetic energy of the particles, resulting in slower reaction rates. Option d - there is nothing you can do to change the speed of the reaction - is not accurate. The reaction rate can be influenced by various factors such as temperature, concentration, catalysts, and surface area, among others. By manipulating these factors, it is often possible to control and change the speed of a reaction. Hence option c, is correct

for more questions on reaction
https://brainly.com/question/4431224
#SPJ8

Answer:

7.5 volts

Explanation:

I did it on USA Testprep

Answer:

Explained below.

Explanation:

We are told that the surface material is ejected into space at a high speed. This means that it will have a likely high momentum as well.

Now, we can say that the total momentum is conserved because the entire asteroid system behaves like an isolated system.

Also, as the surface material is moving with the high momentum like we established earlier, it will cause the asteroid to move with a speed in an opposite direction which also means deflection in an opposite direction.

Answer:

Explained below.

Explanation:

The material ejected from the surface of the asteroid would have a significant momentum. Since the asteroid and all its material is an isolated system, the ejection would cause an oppositely directed change in momentum of the asteroid, according to the law of conservation of momentum.

The ejected material is analogous to gases expelled from a rocket, and the asteroid is analogous to a rocket.

Answer:

50N

Explanation:

is the opposing fotce

Answer:

 P and S waves slow down when they reach this layer. The asthenosphere, also known as the magma chamber, is the uppermost component of the mantle. This layer is partially molten and is a ductile zone in a tectonically poor state.

It's almost hard and seismic waves move through the asthenosphere at a slow rate. The fragile lithosphere and the uppermost portion of the asthenosphere are assumed to be rigid.

seismic waves travel more quickly through denser materials and therefore generally travel more quickly with the depth it moves more slowly through a liquid than a solid. Molten areas within the Earth slow down P waves and stop S waves because their shearing motion cannot be transmitted through a liquid. Partially molten areas may slow down the P waves and attenuate or weaken S waves.

hope this helps...

S and P wave slow down and stop in  the uppermost part of the mantle. - For this, scientists have concluded that the uppermost part of the mantle is partially-molten.

A planetary body's mantle is a layer that is surrounded by the crust on top and the core underneath. The largest and most substantial layer of a planetary body, mantles are often comprised of rock or ice. Planetary bodies that have undergone density differentiation typically have mantles. Mantles are found on all terrestrial planets (including Earth), many asteroids, and a few planetary moons.

Between the crust and the outer core, there is a silicate rock layer known as the Earth's mantle. Despite being mostly solid, it behaves like a viscous fluid over geological time. Oceanic crust is created by the partial melting of the mantle at mid-ocean ridges, and continental crust is created by the partial melting of the mantle at subduction zones.

Learn more about mantle here:

https://brainly.com/question/28827790

#SPJ2

i have no idea

I don't even know how we are here