PROBLEM
Knowing that the tension in rope
AC is F(N), determine the
resultant of the three forces
exerted at point C of post BC.
1100 mm
L=1460 mm
960 mm
B
C
25
24
3
5
4
500 N
200 N
Answers
The resultant of the three forces exerted at point C of post-BC is 475.36 N.
What is the resultant force?The difference between the forces that are acting on an object as part of a system is known as the resultant force. For instance, a resultant force of 7N to the right is produced by a 3N force to the left and a 10N force to the right.
Given, the tension in the rope in the figure.
L=1460 mm
BC = 25
Net force at C = 480i +140j +(160i -120j) +(-240i-275j) = 400i-255j = 475.36
N 32.51 degrees south of east.
Therefore, the resultant of the three forces is 475.36 N.
To learn more about resultant force, refer to the link:
https://brainly.com/question/16380983
#SPJ1
Related Questions
A(n) _____ is an alternate name given to a column or table in any SQL statement.
a.data type
b.alias
c.trigger
d.stored function
Answers
: A uniform slender rod AB rests on a frictionless horizontal surface, and a force P of magnitude 0.25 lb is applied at A in a direction perpendicular to the rod. Assume that the rod weighs 1.85 lb
Answers
To find the acceleration of point A, we can use Newton's second law of motion, which states that the force acting on an object is equal to the mass of the object times its acceleration.
The total force acting on the rod is the force P at point A and the weight of the rod at point B. The weight of the rod is equal to its mass times the acceleration due to gravity, so the total force is:
F_total = P + m_rod * g
Where m_rod is the mass of the rod and g is the acceleration due to gravity.
The acceleration of point A is then:
a = F_total / m_rod
To find the location of the point on the bar that has zero acceleration, we can use the concept of center of mass.
For a uniform rod, the center of mass is located at the midpoint of the rod.
The linear density of the rod is equal to its mass divided by its length, so the length of the rod is:
L = F_total / (m_rod / L)
Solving for L in terms of the given quantities, we find that the length of the rod is:
L = (P + m_rod * g) / (m_rod / L)
This equation can be rearranged and solved to find the value of L.
L^2 = (P + m_rod * g) / (m_rod / L)
L^3 = P + m_rod * g
L^3 - m_rod * g = P
L = (P / (m_rod * g))^(1/3)
Substituting in the given values, we find that:
L = ((0.25 lb) / (1.85 lb * 32.2 ft/s^2))^(1/3) = 0.45 ft
So the length of the rod is 0.45 ft and the location of point B is 0.45 ft from point A.
Here the calculation to find that the midpoint of the rod:
((0.25 lb) + (1.85 lb * 32.2 ft/s^2)) / (2 * (1.85 lb / L)) = 0.225 ft
So the point on the rod that has zero acceleration is located 0.225 ft from point A.
The missing part in the question is shown below.
A uniform slender rod AB rests on a frictionless horizontal surface, and a force P of magnitude 0.25 lb is applied at A in a direction perpendicular to the rod. Assume that the rod weighs 1.85 lb, dib, difermine the acceleration of point a) the acceleration of point A , (c) the location of the point B c) the location of the point on the bar that has zero acceleration.
Learn more about newton's law, here https://brainly.com/question/15280051
#SPJ4
below is the lewis structure of the hydronium ion. count the number of bonding pairs and the number of lone pairs around the oxygen atom.
Answers
Each oxygen atom has two bonding pairs and two lone pairs in the hydrogen peroxide (H2O2) molecule's Lewis structure.
What is the lewis electron dot diagram?The amount of chemical bonds, the bonding atoms, and the lone pairs remaining on the atoms of a particular molecule can all be represented by a lewis structure.Atoms that are bonded to one another are shown by lines, and lone pairs are shown as dot pairs and are placed next to the appropriate atoms.Due to the electrical structure of the oxygen atom, each oxygen atom has six valence electrons.We can observe from the hydrogen peroxide lewis structure that each oxygen atom forms two bonds, one with a hydrogen atom and the other with another oxygen atom.Each oxygen atom in the molecule still possesses one of the two lone pairs.To learn more about lewis electron refer
https://brainly.com/question/20300458
#SPJ4
Design an amplitude modulator using a variable gain amplifier, such as the HMC694LPE. The baseband signal is given by
x(t)=0.5cos(2Ïf 0 t)+0.5cos(4Ïf 0 t)V
The carrier frequency is generated using a dielectric resonator oscillator with an output power of 15dBm at a frequency of 10GHz. The modulated signal should have a mean power of 15dBm with a modulation depth of
+/â5 dB. Download the data sheets of the components from the manufacturer or distributor web sites to design your modulator circuit to meet the specifications. [f 0 =1MHz.]
Answers
Design an amplitude modulator using a variable gain amplifier, such as the HMC694LPE. The baseband signal is given by x(t)=0.5cos(2πf0t)+0.5cos(4πf0t)V The carrier frequency is generated using a dielectric resonator oscillator with an output power of 15dBm at a frequency of 10GHz.
The method of amplitude modulation involves changing the amplitude of the wave signal before it is broadcast. It is frequently used to send information using a radio carrier wave and is known by the abbreviation AM. Electronic communication is where amplitude modulation is most commonly utilised. The modulator is a linear power amplifier that increases the low power level of the modulating signal. Through modulation transformer T1, the modulating output signal is linked to the class C amplifier.The modulating signal and carrier signal's relative amplitudes are Am and Ac. The frequencies of the modulating and carrier signals, respectively, are fm and fc.
To learn more about amplitude modulator click the link below:
brainly.com/question/13265507
#SPJ4
What’s the correct sorting function to list Colors in alphabetical order (A to Z)? A B 29 Color Number 30 Red 100 31 Orange 112 32 Yellow 90 33 Green 85 34 Blue 120 Image not displaying? ASCENDING DESCENDING EQUAL TO A TO Z А 43 npab 44 npce 45 npfo 46 npbb 47 norp 48 49 =COUNTIF(A43:A47,"NP*") Image not displaying? 0 1 O 2 03 04 05
Answers
Choose any cell in the desired column. Click either A-Z to sort ascendingly or Z-A to sort descendingly in the Sort and Filter group on the Data tab.
What sorting function to list colours in alphabetical order?Custom Sort can be found in the Sort & Filter group on the Data tab. Choose the column you want to sort in the Custom Sort dialog box's Columns section. Select Cell Color, Font Color, or Conditional Formatting Icon from the Sort On drop-down menu.
Therefore, Text should be sorted ascendingly. A list of names can be sorted alphabetically, product inventory levels can be listed from highest to lowest, or rows can be sorted by colors or icons.
Learn more about sorting function here:
https://brainly.com/question/29220823
#SPJ4
17. Which of the following best describe ISO 9001:2015? (1) Quality management systems- requirements (1I) Intended to be used in conjunction with ISO 14001 environmental management system (II) ISO 9001 is certifiable by accredited certification bodies (IV) ISO 9001 is only applicable to manufacturers, regardless of size or complexities a. 1& II b. II & III C. 1 &II d. I, II & IV Page 2 of 10 18. "Combination of internal and external issues that can have an effect on an organization's approach to developing and achieving its objectives" is the definition of: Context of the organization a. b. Business environment c. Quality policy d. Quality management system 19. "Systematic, independent and documented process for obtaining objective evidence and evaluating it objectively to determine the extent to which the audit criteria are fulfilled" is the definition of a. Audit b. Internal inspection c. Laboratory testing d. Internal audit procedure 20. Mandatory documented information required by ISO 9001:2015 standard includes Scope of the quality management system (1) Quality objectives (III) Design and development changes (IV) Maintenance of infrastructure (II) a. I, II & IV b. I, II & III c. II, III & IV d. 1, II, III & IV 21. In what clause of ISO 9001:2015 standard is the requirement for conducting internal audit specified? Clause 4 Context of the organization Clause 5 Leadership a. b. Clause 8 Operation C. d. Clause 9 Performance evaluation 22. Audit is a systematic, independent and documented process for obtaining objective evidence and evaluating it objectively to determine the extent to which the audit criteria are fulfilled. Which are the following can be used as objective evidence? Training attendance records Supplier evaluation records Customer satisfaction survey reports Quality objective reports (1) (II) (III) (IV) a. 1& I| b. 1& IV Il & IV C. d. All of the above 23. Audit criteria include ISO 9001:2015 standard (1) (II) (III) (IV) Customer contract requirements Quality manual Operating procedures a. I, II & II b. 1, II & IV c. II, III & IV d. I, II, III & IV audit shall be performed at planned intervals by internal auditors of the organization implementing ISO 9001:2015 quality management system. Please fill in the 24. blank with the best answer. a. Site b. Annual c. Internal d. Supplier Purpose of conducting internal audits includes the following EXCEPT 25. a. To check compliance of the quality management system against ISO 9001:2015 requirements b. To check improvement needs c. To raise non-conformance report for areas not complied to the ISO 9001:2015 standard d. To check effectiveness of the quality management system Purpose of conducting internal audits includes the following EXCEPT 25. To check compliance of the quality management system against ISO 9001:2015 a. requirements b. To check improvement needs c. To raise non-conformance report for areas not complied to the ISO 9001:2015 standard d. To check effectiveness of the quality management system 26. Extent and boundaries of an audit are defined as a. Audit scope b. Audit criteria c. Audit Evidence d. Audit schedule 27. Which of the following are the principles of auditing? (1) (II) (III) Ethical conduct Evidence based approach Due professional care a. 1&II b. II & III I, II & III d. 1& III C. 28. As long as a piece of critical monitoring equipment is periodically used by the operators who know how to use it skillfully, a formalized maintenance and calibration program is not necessary, TRUE or FALSE? a. True b. False
Answers
The sentences that best describe ISO 9001:2015 are:
1) Quality management systems- requirements
2) ISO 9001 is certifiable by accredited certification bodies
3) "Combination of internal and external issues that can have an effect on an organization's approach to developing and achieving its objectives" is the definition of: Context of the organization
4) "Systematic, independent and documented process for obtaining objective evidence and evaluating it objectively to determine the extent to which the audit criteria are fulfilled" is the definition of: Audit
5) Mandatory documented information required by ISO 9001:2015 standard includes: Scope of the quality management system, Quality objectives, Design and development changes, and Maintenance of infrastructure
6) The clause of ISO 9001:2015 standard which is the requirement for conducting internal audit specified is Clause 9: Performance evaluation
7) Audit criteria include: ISO 9001:2015 standard, Customer contract requirements, Quality manual, and Operating procedures
8) Internal audit shall be performed at planned intervals by internal auditors of the organization implementing ISO 9001:2015 quality management system.
9) Purpose of conducting internal audits includes checking compliance of the quality management system against ISO 9001:2015 requirements, identifying improvement needs, and evaluating the effectiveness of the quality management system.
10) Extent and boundaries of an audit are defined as: Audit scope
11) The principles of auditing include: Ethical conduct, Evidence based approach, Due professional care
12) As long as a piece of critical monitoring equipment is periodically used by the operators who know how to use it skillfully, a formalized maintenance and calibration program is not necessary: False
What is an ISO 9001:2015?ISO 9001:2015 determines requirements for a quality management system provided an organization needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements and aims to enhance customer satisfaction through the effective application of the system
Therefore, the correct answer is as given above
learn more about ISO 9001:2015: https://brainly.com/question/28870416
#SPJ1
Determine the absolute maximum shear stress developed in the beam.
Answers
In order to determine the absolute maximum shear stress developed in a beam, you will need to know the following information:
The beam's cross-sectional area: The amount of material that can withstand shear forces will be determined by this.
The shear stress that a beam can withstand before failing will depend on its material qualities.
The beam is being sheared by this force: The amount of shear stress that develops in the beam will depend on this.
The length of the beam will affect how much it deforms when a shear force is applied.
Using this knowledge, you can apply the calculation below to determine the absolute maximum shear stress that has been created in the beam:
Shear force / cross-sectional area equals shear stress.
Remember that the shear force is assumed to be distributed equally over the cross-section of the beam in this formula. The shear stress distribution across the beam may require a more involved analysis if the shear force is not distributed uniformly.
To know more about Shear Stress kindly visit
https://brainly.com/question/12910262
#SPJ4
make a list of the independent variables that influence the punch force in deep drawing of a cylindrical cup, and explain why and how the variables influence this force
Answers
drawing ratio, Blank Diameter, Distance, Strength, thickness of blank, and blank holder force and friction are the independent variables.
What are the independent factors that affect the punch force when a cylindrical cup is drawn deeply?
a) The blank diameter has an impact on the force since a bigger diameter results in a larger circumference and, thus, a higher volume of material that needs to be deformed.
(b) The distance, c, between the punch and die directly affects the force; the higher the thickness decrease, the larger the labor required.
(c) The yield strength and strain-hardening exponent of the workpiece have an impact on the force because as these qualities rise, more forces are needed to generate deformation beyond yielding.
(d) The thickness of the blank also causes more volume to be distorted, which raises the force.
(e) Because friction and the blankholder force limit the amount of material that can flow into the die, more energy must be supplied to overcome these forces.
To know more about force, visit: https://brainly.com/question/14071789
#SPJ4
Consider the following scenario. R1 R2 R3 P1 3 3 3 P2 2 1 R1 P1 2 P2 1 R2 R3 1 1 1 1 NN R1 R2 R3 1 1 0 P3 1 1 P3 1 1 0 P1 Available vector Claim matrix Allocation matrix Using banker's algorithm what is safe sequence. (A) P2, P3, P1 (B) P1, P2, P3 (C) P3, P2, P1 (D) None of the above
Answers
Since all processes have a finish value of true, the safe sequence is P2, P3, P1. Therefore, the correct answer is (B) P1, P2, P3.
To find the safe sequence using the Banker's algorithm, you need to perform the following steps:
Calculate the need matrix for each process by subtracting the allocation matrix from the maximum demand matrix.Initialize the work array to the available vector and the finish array to false for all processes.Find a process with a finish value of false that has a need less than or equal to the work array. If such a process is found, allocate resources to that process and update the work and finish arrays.Repeat step 3 until either there are no more processes with a finish value of false or no such process can be found.Using these steps, we can find the safe sequence for the given scenario as follows:
Need matrix:
P1: 3-2=1, 3-3=0, 3-3=0
P2: 2-1=1, 1-1=0, 0-0=0
P3: 1-1=0, 1-1=0, 1-0=1
Work array: [2, 1, 1]
Finish array: [false, false, false]
Step 1: Process P2 has a need of [1, 0, 0] which is less than or equal to the work array, so it can be allocated resources. Update work array to [2-1=1, 1-0=1, 1-0=1] and set finish[P2]=true.
Work array: [1, 1, 1]
Finish array: [false, true, false]
Step 2: Process P3 has a need of [0, 0, 1] which is less than or equal to the work array, so it can be allocated resources. Update work array to [1-0=1, 1-0=1, 1-1=0] and set finish[P3]=true.
Work array: [1, 1, 0]
Finish array: [false, true, true]
Step 3: Process P1 has a need of [1, 0, 0] which is less than or equal to the work array, so it can be allocated resources. Update work array to [1-1=0, 1-0=1, 0-0=0] and set finish[P1]=true.
Work array: [0, 1, 0]
Finish array: [true, true, true]
Thus, the right answer is (B) P1, P2, P3.
Learn more about algorithm, here https://brainly.com/question/22984934
#SPJ4
Which of the following must be considered when determining the size of the conductor required to connect an electrical load to the source of supply?
Answers
When choosing circuit conductors, four aspects should be taken into account: current flow, voltage, voltage drop over distance, and heat resistance.
Three key criteria are used to determine the cable size: the carrying capacity right now. voltage control. Rating for short circuits. What elements determine the conduit and tubing sizes needed for an installation? Conductor count, cross-sectional area, and permitted raceway fill.
To avoid overheating and fire, the NEC specifies conductor minimum sizes. Three main variables affect how big a conductor needs to be to safely carry the current forced upon it: insulation type, ambient temperature, and conductor bundling.
Kelvin's law determines the appropriate size of the conductor for transmission lines (given by Lord Kelvin in 1881).
Know more about installation here:
https://brainly.com/question/13267432
#SPJ4
Conditions connected by OR will be true O when both conditions are false only when both conditions are true O when either condition is true Oonly when just one condition is true
Answers
Condition connected by OR will be true when either condition is true.
What is OR in logical operator?OR or in some programming language is symbolized as "||" is logical operator to give the result as true when at least one condition is true.
The opposite of OR is AND or can be symbolized as "&&" that required all of condition is true to give the result as true.
So, the first option is absolutely incorrect. The second and the fourth option is not quite right. Thus, the best option is the third option which is when either condition is true.
You question is incomplete, but most probably your full question was
(image attached)
Learn more about logical operator here:
brainly.com/question/15079913
#SPJ4
What i the relationhip between the weight of a Viking boat and water diplacement?
Answers
The weight of the water displaced is calculated as the product of the ship's water displacement volume and water density. Displacement is therefore equal to ship weight.
Every floating object displaces its own weight in the liquid in which it is submerged according to the Archimedes principle. A vessel's weight must match the weight of the volume of water it removes in order for it to float freely in the water. The amount of water that a vessel displaces is known as displacement.
The buoyant force acting on the object will be equal to gravity if it displaces an amount of water equal to its own weight, at which point the object will float. However, if an object weighs more than the volume of water it moves, it will sink since the buoyant force will be greater than gravity.
Know more about force here:
https://brainly.com/question/9473432
#SPJ4
lace the force system by a wrench and specif 4-135. Replace the for nitude of the force and couple moment of the wrench oint where the wrench intersects the x-z plane. the magnit e magnitu and the poin d the p 2 200 N 400 N 0.5 m 200 N 4 3 m 2 m Prob. 4-135
Answers
To replace the force system shown in Prob. 4-135 with a wrench, you will need to determine the magnitude and direction of the force and couple moment that the wrench should exert.
You can do this by taking the following actions:
Identify the net force influencing the system: You can accomplish this by adding up the various forces that are at work on the system. The net force in this situation is 200 + 400 = 600 N.
The system's net couple moment can be calculated by: This is accomplished by adding the two moments of the various forces at the wrench's x-z plane intersection. The net couple moment in this scenario is calculated as (0.5 m)(200 N) - (4 m)(200 N) - (3 m)(400 N) = -600 N*m.
Calculate the wrench's pair moment and force, taking into account their magnitude and direction: The equations for the force and couple moment of a wrench can be used for this.
To know more about Wrench kindly visit
https://brainly.com/question/10186385
#SPJ4
Please answer thank you!
Answers
A sophisticated tool for doing static analysis of trusses is called 2D Truss Analysis. It uses optimized finite elements (bar elements).
How do you solve a truss Determinacy?The 2D-Truss Analysis By using their two locations, identify the structure's node points.The two nodes (or mouse-dragging between two nodes) and material number of each truss element should be specified.the material information (cross-section and Young's modulus) Specify the loads.
If a truss can be completely estimated using only the equations of static equilibrium, it is said to be statically determinate. In order for a planar truss to be statically determinate, the sum of the members and support reactions cannot be greater than the number of joints divided by 2.It is a leader-product in truss analysis due to its adaptable interface and simple modification. attributes for analysis.
To learn more about 2D truss refer to :
https://brainly.com/question/13685762
#SPJ1
A PBX/PABX has seven telephone channels to a public exchange.During the busy hour on average 3.4 lines are occupied (a) what is the traffic intensity during the busy hour?
Answers
Enthalpy Changes the overall energy change in the substance portrayed in the graph at 48°C.
What are the data that were obtained from the question?Mass (m) = 0.3 Kg
Initial temperature (T1) = 20°C
Heat (Q) added = 35 KJ
Specific heat capacity (C) = 4.18 KJ/Kg°C
Final temperature (T2)
The final temperature of water can be obtained as follow:
Q = MC(T2 – T1)
35 = 0.3 x 4.18 (T2 – 20)
35 = 1.254 (T2 – 20)
Clear the bracket
35 = 1.254T2 – 25.08
Collect like terms
1254T2 = 35 + 25.08
1.254T2 = 60.08
Divide both side by the coefficient of T2 i.e 1.254
T2 = 60.08/1.254
T2 = 47.9 ≈ 48°C
Therefore, the final temperature of the water is 48°C.
Learn more about temperature on:
https://brainly.com/question/11464844
#SPJ1
3-21 Complete this table for H2O: T. C P. kPa u, kJ/kg Phase description 400 1450 220 Saturated vapor 190 2500 4000 3040
Answers
The complete table for H₂O is shown below:
a) T (°C): 143.6, Phase description: Superheated water vapor
b) P, (Kpa): 2318 , u(kJ/Kg): 2602.4.
c) u(kJ/Kg):805.53, Phase description: Compressed liquid water
d) T (°C): 466.73, Phase description: Superheated water vapor
Thermodynamics is the study of heat, work, and energy and how these quantities are related to each other. It aims to understand and predict the behavior of systems that exchange energy with their surroundings. The laws of thermodynamics provide a set of fundamental principles that can be used to analyze the behavior of systems and predict how they will behave under different conditions.
Here is the calculation for c and d:
c) Slope = (849.9 - 761.16) / (200 - 180) = 4.437
d) Intercept = 849.9 - 4.437 * 200 = 805.53 [kJ/kg]
Learn more about H₂O, here https://brainly.com/question/29711632
#SPJ4
if a ball joint has a threaded plug, the plug can be removed and a fitting installed that will allow the ball joint to be greased periodically.
Answers
If a ball joint has a threaded plug, the plug can be removed and replaced with a Zerk fitting, allowing the ball joint to be greased on a regular basis.
What are Ball joints?
Ball joints are a component of a car's front suspension. The front suspension is a complex assembly of links, joints, bushings, and bearings that allow your front wheels to move independently up and down as well as turn left or right. Ball joints allow suspension movement, which increases tire contact with the road, resulting in better vehicle control and tire wear.
What are ball joints used for?
Ball joints are a critical component of the front suspension that connect and move various links. Ball joints, like the human hip joint, are made up of a ball and a socket. Your front suspension's ball joints pivot between the steering knuckles and control arms to provide a safe, smooth ride and precise control of your vehicle.
To know more about ball joint, visit: https://brainly.com/question/14318856
#SPJ4
which of the following will reduce the induced voltage in a wire being moved through a magnetic field
Answers
As a result, induced voltage will drop as the coil's turn count is reduced. This phenomena is explained by Faraday's Law.
According to Faraday's Law, if a conductor is a part of a closed circuit, an electric current will flow whether the conductor is passed through a magnetic field or the magnetic field is moved past the conductor.
We are aware that if a static conductor is placed within a fluctuating magnetic field or if a conductor moves within a static magnetic field, a voltage will be induced. This phenomena is explained by Faraday's Law.
Changes to the magnetic field's strength, the conductor's movement in and out of the field, the distance between a magnet and the conductor, or the size of a loop in the field can all result in this shift.
Know more about loop here:
https://brainly.com/question/14390367
#SPJ4
As new students begin to arrive at college, each receives a unique ID number, 1 to n . Initially, the students do not know one another, and each has a different circle of friends. As the semester progresses, other groups of friends begin to form randomly. There will be three arrays, each aligned by an index. The first array will contain a queryType which will be either Friend or Total. The next two arrays, students1 and students2, will each contain a student ID. If the query type is Friend, the two students become friends. If the query type is Total, report the sum of the sizes of each group of friends for the two students. Example n=4 queryType = ['Friend', 'Friend', 'Total'] student 1=[1,2,1] student2 =[2,3,4] The queries are assembled, aligned by index: Input from stdin will be processed and passed to the function as follows: The first line contains an integer n , the number of students. The next line contains an integer q , the number of queries. Each of the next q lines contains a string queryType[i] where 1≤i≤q . The next line contains an integer q , the number of queries. Each of the next q lines contains a string students1[i] where 1≤i≤q . The next line contains an integer q , the number of queries. Each of the next q lines contains a string students2[i] where 1≤i≤q . Sample Case 0 Sample Input 0 STDIN −0 3 2 Friend → query = [’Friend’, ’Tota Total 2 1 2 2 2 Function −0.0 →n=3 → queryType [ ] size q=2 → students 1[] size q=2 → students 1=[1,2] → students 2[] size q=2 → students2 =[2,3] Sample Output 0 3 Fynlanation 0
Answers
This is a test case-based Cp issue, and the C++ language is used for the solution.
What is for loop?Programmers use the for loop, a conditional iterative statement, to check for certain conditions, and if they are satisfied, they repeatedly run a block of code.
The explicit loop number or loop variable that enables the body of the loop to know the precise sequencing of each iteration sets the for loop apart from other looping expressions.
Given:
As new students begin to arrive at college, each receives a unique ID number, 1 to n.
Given example:
n=4
query Type=['Friend','Friend', 'Total']
student1=[1,2,1]
student2=[2,3,4]
The queries are assembled, aligned by index: Input from stdin will be processed and passed to the function as follows:
We have to write a program to pass the test cases of this problem, so let us write the solution.
This is a c+ problem which is a test case based problem and the solution is in c++ language.
So,
#include<bits/stdc++.h>
using namespace std;
const int Mx=1e5+5;
int par[Mx],cnt[Mx];
void ini(int n){
for(int i=1;i<=n;++i)par[i]=i,cnt[i]=1;
}
int root(int a){
if(a==par[a])return a;
return par[a]=root(par[a]);
}
void Union(int a,int b){
a=root(a);b=root(b);
if(a==b)return;
if(cnt[a]>cnt[b])swap(a,b);
par[a]=b;
cnt[b]+=cnt[a];
}
int* getTheGroups(int n,int q,int sz,string queryTypes[],int student1[],int student2[],int* ans){
ini(n);
int current=0;
for(int i=0;i<q;++i){
if(queryTypes[i]=="Friend"){
Union(student1[i],student2[i]);
}
else{
int x=root(student1[i]),y=root(student2[i]);
if(x==y)ans[current++]=cnt[x];
else ans[current++]=cnt[x]+cnt[y];
}
}
return ans;
}
int main(){
int n,q,sz=0;
cin>>n>>q;
string queryTypes[q];
int student1[q],student2[q];
for(int i=0;i<q;++i){
cin>>queryTypes[i];
if(queryTypes[i]=="Total")
++sz;
}
cin>>q;
for(int i=0;i<q;++i)cin>>student1[i];
cin>>q;
for(int i=0;i<q;++i)cin>>student2[i];
int ans[sz];
int* ptr=getTheGroups(n,q,sz,queryTypes,student1,student2,ans);
for(int i=0;i<sz;++i)
cout<<ptr[i]<<endl;
return 0;
}
Therefore, this is a c+ problem which is a test case based problem and the solution is in c++ language.
To learn more about the for loop;
https://brainly.com/question/28300701
#SPJ4
we are interested in generating functions for the number of different ways to compose a bag of n donuts subject to various restrictions. for each of the restrictions in parts (a)-(e) below, find a closed form for the corresponding generating function. (a) all the donuts are chocolate and there are at least 3.
Answers
the donuts are chocolate and there are at least
(a) All the donuts are chocolate and there are at least 3, therefore, x³/1 − x.
What is function?A function from a set X to a set Y in mathematics assigns each element of X exactly one element of Y. The domain and codomain of the function are denoted by the sets X and Y, respectively. [Reference required]
The concept of function was first discussed by two Persian mathematicians named Al-Biruni and Sharaf al-Din al-Tusi. Functions were originally used to represent the idealised relationship between varying quantities and other variables. For example, time has an impact on a planet's position.
The concept was first developed at the end of the 17th century with the infinitesimal calculus, and up until the 19th century, the functions taken into account were differentiable.
Learn more about function
https://brainly.com/question/22340031
#SPJ4
How can I compare similar sites?
Answers
Compare similar sites:
1. Compare the design, layout, and navigation of each site.
2. Compare the content, including the quality and quantity of text, images, video, and audio.
3. Compare the performance of the sites, such as page loading speed, usability, and responsiveness.
4. Compare the features of each site, including search functionality, account creation, ecommerce features, and more.
5. Compare the SEO performance of each site, such as keyword targeting, backlinks, and domain authority.
6. Compare the analytics data from each site to get an idea of user behaviour and engagement.
7. Compare the user feedback from each site to get an idea of user satisfaction.
What is sites?
Sites are a word used to describe webpages or websites. A website is a collection of related webpages, images, videos, and other digital assets that are hosted on a server, and accessed through a domain name or URL. A website can contain a range of different types of content, such as text, images, audio, video, and other interactive elements. Websites are typically used to provide information, services, or products to people around the world, and to connect people with one another. Websites are created and maintained by web developers and designers, and are typically hosted on web servers.
To learn more about sites
https://brainly.com/question/29561548
#SPJ1
Which Of The Following Would Most Likely Occur As The Direct Result Of The Second Collision. Air bubbles in the arterial blood vessels. Which of the following would most likely occur as the direct result of the second collision in a motor vehicle crash?
Answers
Deformed steering wheel Of The Following Would Most Likely Occur As The Direct Result Of The Second Collision. Air bubbles in the arterial blood vessels.
What is the 2nd collision in a crash?The second collision is the “human collision.” At the moment of impact, passengers in the car that are unrestrained are still travelling at the vehicle's original speed.
What happens in the second stage of a crash the human crash?Stage 2: Human Collison During the second stage of “human collision,” all occupants in the vehicle will still be moving in the same direction and speed as they were before the collision happened. Inertia will keep the occupants moving toward the point of an impact unless a seatbelt or airbag stops them.
To know more about Second Collision visit :-
https://brainly.com/question/1871060
#SPJ4
It is desired to design a modulo-6 counter circuit that counts repeatedly through the length- 6 sequence of decimal numbers in that order:
[0,4,5,2,3,1,â¦]
Using three D-flip-flops, Q2 ,Q 1 ,Q 0 , with Q 2 representing the most-significant-bit of the decimal sequence and Q 0, the least-significant-bit, show that the required next-state flip-flop excitation equations for the counter will be as follows, where you only need to determine the correct expression for
â
Answers
Three D-type flip-flops are all that are needed to construct a divide-by-6 counter, also known as a modulo 6 (MOD-6) counter circuit. The counter is set up so that it counts from 0 to 5 and then automatically resets on the sixth count to start over.
It is unstable because we are using the sixth count itself to reset. Start with a MOD-B counter and look for the binary sequence 110, which is 6 in decimal, to get the trick. We look for the sequence of 1s and feed them into an AND gate because this binary sequence is unique. The RESET function on each of the three flip-flops is then controlled by the output of the AND gate. Keep in mind that the counter output is from left to right while binary is read from right to left (LSB to MSB). Here, students are likely to make mistakes and feed the AND gate with the wrong outputs.
One of the most important uses for shift registers is in Johnson counters. They are made by connecting the complement of the output of the last flip-flop to the input of the first flip-flop and connecting multiple flip-flops so that one flip-flop's output serves as the input for another.
A mod 6 Johnson counter requires three flip-flops. Keep in mind that a Johnson counter requires half as many flip-flops as it uses in states. Three flip flops will be needed because a mod 6 Johnson counter can count up to six states.
Because a Johnson counter is a synchronous counter like a ring counter, state transitions cannot occur unless the clock is in the "ON" state.
To know more about counter circuit visit
brainly.com/question/29375541
#SPJ4
solved using filter, write an oz function which selects from a list of integers those which are positive. for example, if the input is [1 ~2 3 ~4], the output should be [1 3].
Answers
To write an oz function which selects from a list of integers those which are positive. for example, if the input is [1 ~2 3 ~4], the output should be [1 3], checl the code given below.
What is Oz?In the Programming Systems Lab at the Université catholique de Louvain, a multiparadigm programming language called Oz was created for the purpose of teaching programming. The Concepts, Techniques, and Models of Computer Programming textbook is considered to be the bible of the subject.
Gert Smolka and his pupils created Oz for the first time in 1991. Together with Seif Haridi and Peter Van Roy's research team at the Swedish Institute of Computer Science, Oz's development was continued in 1996. The Mozart Consortium, a global organization that was founded in 1999 by Saarland University, the Swedish Institute of Computer Science, and Université catholique de Louvain, has been continuously working on Oz since that time.
//CODE//
fun {Map Xs}
case Xs of nil then nil
[] X|Xr then X|{Filter Xr fun {$ X} X>=0 end}
end
end
{System.show {Map [1 ~2 3 4]}}
Output will be [1 3 4]
Learn more about programming language
https://brainly.com/question/16936315
#SPJ4
1) Which of the following are true about Defragmentation? (multiple answers may apply): Group of answer choices - Physically organizes the contents of the mass storage device used to store files into the smallest number of contiguous regions. - It is applicable to file systems on electromechanical disk drives. - It speeds up the movement of the hard drive's read/write heads by accessing now sequentially de-fragmented files. - It seeks to reverse the fragmentation of long contiguous regions into smaller and smaller contiguous areas that happens over time. 2) The NTFS file system is characterized by? Group of answer choices - Its compatibility with other systems like Linux, MAC OS and Sony’s PlayStation. - File-by-file compression, full permissions for security control and attribute settings and a change journal that can help quickly recover errors if your computer crashes. - It is generally ideal for flash drives. 3) What is true about a File Name? (multiple answers may apply) Group of answer choices - A file name is used to identify a storage location in the file system. - File names can have restrictions on the use of certain special characters, disallowing them within file names. - File names are always case sensitive. - Most file systems have restrictions on the length of file names.
Answers
The following are true about Defragmentation:
It physically organizes the contents of the mass storage device used to store files into the smallest number of contiguous regions.It is applicable to file systems on electromechanical disk drives.It seeks to reverse the fragmentation of long contiguous regions into smaller and smaller contiguous areas that happens over time.Hence, option A, B and C are correct.
What is Defragmentation about?The NTFS file system is characterized by:
File-by-file compression, full permissions for security control and attribute settings, and a change journal that can help quickly recover errors if your computer crashes.Therefore, The following are true about a File Name:
A file name is used to identify a storage location in the file system.File names can have restrictions on the use of certain special characters, disallowing them within file names.File names are often case sensitive.Most file systems have restrictions on the length of file names.Learn more about Defragmentation from
https://brainly.com/question/14254444
#SPJ1
solved using the type notation, write two oz functions for determining the sum of the elements of: a) nested list, given by: ::
Answers
The two functions of nested list will be:
[[Int]]
sumNestedList :: [[Int]] -> Int
sumNestedList xs = sum (map sum xs)
sumNestedList2 :: [[Int]] -> Int
sumNestedList2 = foldr (\x acc -> sum x + acc) 0
What is nested list?
A nested list is a list of lists, or a list that contains other lists as elements. It is an effective way to organize and store data in a hierarchical structure. Nested lists are useful for organizing data into categories and subcategories, such as products and their sub-components or ingredients. A nested list is also a way to represent a tree data structure, which is a type of hierarchical data structure that consists of nodes connected by directed edges. Nested lists can also be used to represent graphs, networks, and other complex data structures.
To learn more about nested list
https://brainly.com/question/15048204
#SPJ4
Which consequences can victims of identity theft face? check all that apply.
Answers
difficulty getting a loan or credit card
an increase in debt
difficulty keeping assets
a loss of money
Answer:
Difficulty getting a loan or credit card.
An increase in debt.
Difficulty keeping assets.
A loss of money.
Explanation:
5.21. Compute the Fourier transform of each of the following signals: (a) x[n] = a[n-2] - [n-6] (b) x[n] = (-ul-n-1] (c) x[n] = (-1-2 (d) x[n] 2* sin(n)ul-n) (e) x[n] = (cos(in-1)) (f) x[n] n. -3 ns3 0, otherwise (g) x[n] = sin(n) + cos(n) (h) x[n] = sin(n) + cos(n) (i) x[n] = x[n-6), and x[n] = a[n] - x[n- 5] for 0 Sns 5 G) x[n] = (n-1) (k) x[n] = (simis cos(n)
Answers
The Fourier transform of each signal :
x[n] = a[n-2] - [n-6] →X(ω) = A(ω)e^2ω - A(ω)e^6ωx[n] = -u[-n-1] → X(ω) = A(ω)e^(-jω) x[n] 2* sin(n)ul-n) → X(ω) = 2A(ω)sin(ω) x[n] = (cos(n-1)) → X(ω) = A(ω)cos(ω-1) x[n] = sin(n) + cos(n) → X(ω) = A(ω) (sin(ω) + cos(ω))x[n] = sin(n) + cos(n) → X(ω) = A(ω) (sin(ω) + cos(ω))x[n] = x[n-6] + x[n+6] → X(ω) = A(ω) (e^6ω + e^-6ω) x[n] = a[n-2] - [n-6]The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is a[n-2] - a[n-6], so we can rewrite this as x[n] = a[n]e^2ω - a[n]e^6ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:
X(ω) = ∑(a[n]e^2ω - a[n]e^6ω) e^-jnω
= ∑a[n]e^2ωe^-jnω - ∑a[n]e^6ωe^-jnω
= A(ω)e^2ω - A(ω)e^6ω
Therefore, the Fourier transform of x[n] = a[n-2] - a[n-6] is X(ω) = A(ω)e^2ω - A(ω)e^6ω.
x[n] = -u[-n-1]The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is -u[-n-1], so we can rewrite this as x[n] = -u[n+1]e^-j(n+1)ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:
X(ω) = ∑(-u[n+1]e^-j(n+1)ω) e^-jnω
= -∑u[n+1]e^-jω
= -A(ω)e^-jω
Therefore, the Fourier transform of x[n] = -u[-n-1] is X(ω) = -A(ω)e^-jω.
x[n] 2* sin(n)ul-n)The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is 2*sin(n)u[-n], so we can rewrite this as x[n] = 2*sin(n)e^-jnω. We can then use the Fourier transform formula to find the Fourier transform of the signal:
X(ω) = ∑(2*sin(n)e^-jnω) e^-jnω
= 2∑sin(n)e^-jnω
= 2A(ω)sin(ω)
Therefore, the Fourier transform of x[n] = 2*sin(n)u[-n] is X(ω) = 2A(ω)sin(ω).
x[n] = (cos(n-1))The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is (cos(n-1)), so we can rewrite this as x[n] = cos(n-1)e^-j(n-1)ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:
X(ω) = ∑(cos(n-1)e^-j(n-1)ω) e^-jnω
= ∑cos(n-1)e^-jω
= A(ω)cos(ω-1)
Therefore, the Fourier transform of x[n] = (cos(n-1)) is X(ω) = A(ω)cos(ω-1).
x[n] = sin(n) + cos(n)The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is sin(n) + cos(n), so we can rewrite this as x[n] = sin(n)e^-jnω + cos(n)e^-jnω. We can then use the Fourier transform formula to find the Fourier transform of the signal:
X(ω) = ∑(sin(n)e^-jnω + cos(n)e^-jnω) e^-jnω
= ∑sin(n)e^-jnω + ∑cos(n)e^-jnω
= A(ω) (sin(ω) + cos(ω))
Therefore, the Fourier transform of x[n] = sin(n) + cos(n) is X(ω) = A(ω) (sin(ω) + cos(ω)).
x[n] = sin(n) + cos(n)
The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is sin(n) + cos(n), so we can rewrite this as x[n] = sin(n)e^-jnω + cos(n)e^-jnω. We can then use the Fourier transform formula to find the Fourier transform of the signal:
X(ω) = ∑(sin(n)e^-jnω + cos(n)e^-jnω) e^-jnω
= ∑sin(n)e^-jnω + ∑cos(n)e^-jnω
= A(ω) (sin(ω) + cos(ω))
Therefore, the Fourier transform of x[n] = sin(n) + cos(n) is X(ω) = A(ω) (sin(ω) + cos(ω)).
x[n] = x[n-6] + x[n+6]
The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is x[n-6] + x[n+6], so we can rewrite this as x[n] = x[n]e^-6ω + x[n]e^6ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:
X(ω) = ∑(x[n]e^-6ω + x[n]e^6ω) e^-jnω
= ∑x[n]e^-6ωe^-jnω + ∑x[n]e^6ωe^-jnω
= A(ω) (e^6ω + e^-6ω)
Therefore, the Fourier transform of x[n] = x[n-6] + x[n+6]
Learn more about Fourier transform:
https://brainly.com/question/28984681
#SPJ4
Is an electoral system where legislators are elected at large and in which parties receive electoral representation in relation to the total votes they receive.
Answers
Democracy: is an electoral system where legislators are elected at large and in which parties receive electoral representation in relation to the total votes they receive.
What is democracy?Democracy can be defined as a type of government that is established by the people and generally for the people. This ultimately implies that, a democracy refers to a type of government that accords all the power to the people.
This simply means that, that the form of power that is exercised through the people is generally referred to as democracy. Additionally, all the people living in a country that practice democracy are expected to elect legislators at large.
In this context, we can infer and logically deduce that political parties receive electoral representation with respect to the total votes they receive under a democracy.
Read more on democracy here: brainly.com/question/3710021
#SPJ1
Assume int[] t = {1, 2, 3, 4). What is t·length? 0
3
4
5
Answers
Correct option is 4