False. The force between two parallel wires carrying electric current can either attract or repel the wires, depending on the direction of the currents.
The force follows Ampere's right-hand rule, which states that if the currents in the wires are in the same direction, the wires repel each other, and if the currents are in opposite directions, the wires attract each other. Therefore, the force between the two wires can pull them together or push them apart, depending on the direction of the currents.
Learn more about Ampere's right-hand rule here:
https://brainly.com/question/32250956
#SPJ11
The modulus of elasticity for a ceramic material having 5 vol% porosity is 296 GPa (43x10^6 psi). (a) Compute the modulus of elasticity for the nonporous material. (b) At what volume percent porosity will the modulus of elasticity be 231 GPa (33x10^6 psi)?
(a) The modulus of elasticity for the nonporous ceramic material is 365 GPa (52.9 x 106 psi).(b) At 12.8 vol% porosity, the modulus of elasticity of the ceramic material will be 231 GPa (33 x 106 psi)
Given data: The modulus of elasticity of a ceramic material having 5 vol% porosity = 296 GPa. The modulus of elasticity of a nonporous ceramic material = ?. Now, we know that the modulus of elasticity for a porous ceramic material can be calculated using the following relationship: where E is the modulus of elasticity of porous material, E0 is the modulus of elasticity of nonporous material, and n is the porosity volume percentage.
Using the above formula, we can solve the equation as follows:296 GPa = E0(1 – 0.05)E0 = 296 / 0.95 = 311 GPa. The modulus of elasticity for nonporous ceramic material is 311 GPa. The modulus of elasticity of the porous ceramic material can be found using the following formula: where E is the modulus of elasticity, E0 is the modulus of elasticity of nonporous material, and n is the porosity volume percentage. Using the formula, we get:231 x 106 psi = 311 x 106 psi (1 - n)n = 0.128 or 12.8 vol%. Therefore, at 12.8 vol% porosity, the modulus of elasticity of the ceramic material will be 231 GPa (33 x 106 psi).
know more about modulus of elasticity
https://brainly.com/question/30756002
#SPJ11
classical elements favored by the renaissance architects included:
Classical elements favored by Renaissance architects included:
1. **Symmetry and Proportion**: Renaissance architects drew inspiration from the classical architecture of ancient Rome and Greece. They emphasized the use of symmetrical designs and proportions based on mathematical principles such as the golden ratio. Buildings were carefully balanced and harmonious in their proportions.
2. **Columns and Capitals**: Renaissance architecture incorporated classical elements such as columns and capitals. Columns, especially the Doric, Ionic, and Corinthian orders, were used to support structures and provide a sense of elegance and grandeur. Capitals, the decorative tops of columns, were intricately designed with ornamental details.
3. **Architectural Orders**: Renaissance architects embraced the classical architectural orders, which consisted of specific proportions and ornamentation. These orders included the Doric, Ionic, and Corinthian orders, each with its distinctive characteristics and decorative elements.
4. **Architectural Elements**: Renaissance architects incorporated various classical elements into their designs, such as pediments, pilasters, arches, vaults, domes, and entablatures. These elements added depth, visual interest, and architectural sophistication to buildings.
5. **Classical Motifs and Ornamentation**: Renaissance architecture featured classical motifs and ornamentation, including motifs such as acanthus leaves, rosettes, garlands, and sculptural reliefs. These decorative elements adorned facades, cornices, and interiors, showcasing the influence of classical aesthetics.
By integrating these classical elements into their designs, Renaissance architects sought to evoke the beauty, harmony, and timelessness associated with the architecture of ancient Greece and Rome. Their revival of classical principles became a hallmark of the Renaissance architectural style.
Learn more about Architectural Elements here:
https://brainly.com/question/29333161
#SPJ11
if a stepper motor is currently at state 1001 for windings a, b, c and d respectively, what is the next state required in order to progress the motor counter-clockwise? a) 0011. b) 1001. c) 1100. d) 0110.
The correct answer to this question is option (c) 1100.
Explanation: If a stepper motor is currently at state 1001 for windings a, b, c, and d respectively, the next state required to progress the motor counter-clockwise is 1100. A stepper motor is a type of brushless DC electric motor that converts digital pulses into mechanical shaft rotation. Stepper motors are divided into two categories based on their torque, namely, permanent magnet and hybrid stepper motors.The torque of permanent magnet stepper motors is low, and they are less efficient than hybrid stepper motors. Hybrid stepper motors are a mixture of permanent magnet and variable reluctance stepper motors. They provide excellent performance at a reasonable price. Hybrid stepper motors are widely used in a variety of applications.
Learn more about Stepper motors here https://brainly.in/question/19353702
#SPJ11
Consider a mild steel specimen with yield strength of 43.5 ksi and Young's modulus of 29,000 ksi. It is stretched up to a point where the strain in the specimen is 0.2% (or 0.002). If the specimen is unloaded (i.e. load reduces to zero), the residual strain (or permanent set) is: 0.05% 0.1% 0% 0.2%
Answer:
0.05%
Explanation:
From the question, we have;
The yield strength of the mild steel, [tex]\sigma _c[/tex] = 43.5 ksi
Young's modulus of elasticity, ∈ = 29,000 ksi
The total strain, [tex]\epsilon _c[/tex] = 0.2% = 0.002
The inelatic strain [tex]\epsilon_c^{in}[/tex] is given as follows;
[tex]\epsilon_c^{in}[/tex] = [tex]\epsilon _c[/tex] - [tex]\sigma _c[/tex]/∈
Therefore, we have;
[tex]\epsilon_c^{in}[/tex] = 0.002 - 43.5/(29,000) = 0.0005
Therefore, the inelastic strain, [tex]\epsilon_c^{in}[/tex] = 0.0005 = 0.05%
Taking the inelastic strain as the residual strain, we have;
The residual strain = 0.05%
his exercise examines the single error correcting, double error detecting (SEC/DED) Hamming code. [5] <$5.5> Section 5.5 states that modern server memory modules (DIMMs) employ SEC/DED ECC to protect each 64 bits with 8 parity bits. Compute the cost/performance ratio of this code to the code from Exercise 5.14.1. In this case, cost is the relative number of parity bits needed while performance is the relative number of errors that can be corrected. Which is better?
Explanation:
Given,In case of Single error correcting and double error detecting (SEC/DED) Hamming code,modern server memory modules (DIMMs) are used for protection of each 64 bits with 8 parity bits.This exercise examines the SEC/DED Hamming code.Now we need to compute the cost/performance ratio of this code to the code from Exercise 5.14.1. In this case, cost is the relative number of parity bits needed while performance is the relative number of errors that can be corrected.Since this is a SEC/DED Hamming code, each 64 bits will be protected with 8 parity bits. So,Total bits per word=n=64Total parity bits=k=8Hence, The cost of the code will be the relative number of parity bits needed, which is the ratio of the number of parity bits to the number of data bits.c = k / n = 8 / 64 = 1 / 8Also, the performance of the code is the relative number of errors that can be corrected. In case of SEC/DED Hamming code, Single bit error can be corrected while double bit error can be detected.p = 1 (Single bit error can be corrected)Therefore, the cost/performance ratio of the code will be:c/p = (1/8) / 1= 1/8Now, we need to compare the cost/performance ratio of this SEC/DED code with the code from Exercise 5.14.1.We know,In case of SEC code, 1 parity bit is used for each 16 data bits.So, for n = 64, number of parity bits needed will be 4. Hence,c = k / n = 4 / 64 = 1 / 16Also, 1-bit error can be corrected. Hence,p = 1Therefore, the cost/performance ratio of SEC code will be:c/p = (1/16) / 1= 1/16Now, to compare, we need to find the better ratio of the two. It is better when the cost is less and the performance is more.Comparing both, we have,c/p(SEC/DED Hamming code) = 1/8c/p(SEC code) = 1/16
Hence, the SEC/DED Hamming code has a better cost/performance ratio.
Learn more about (SEC/DED) here https://brainly.in/question/8547556
#SPJ11
Starting with the simplest approximation, cos x = 1, add terms one at a time to estimate cos(π/3) (see Problem 2 in Lecture 5). (a) After each new term is added, compute the true and approximate percent relative errors. Use a calculator to determine the true value. Add terms until the absolute value of the approximate error estimate falls below an error criterion conforming to two significant figures. (b) Rename M-file function Maclaurin.m (available in Files/Lectures/05) to Maclaurin_cos.m, modify, and adapt it for evaluating the Maclaurin series expansion for cos x. Implement fprintf inside while loop to display for each iteration the following output: iteration number, approximate value of cos(π/3), true percent relative error, approximate percent relative error. Report your M-file and output results for cos(π/3).
function [fxa,fxt,et,ea,iter] = Maclaurin(x,es,maxit)
% Maclaurin series of exponential function
% [fxa,fxt,et,ea,iter] = Maclaurin(x,es,maxit)
% input:
% x = value at which series evaluated
% es = stopping criterion (default = 0.0001)
% maxit = maximum iterations (default = 100)
% output:
% fxa = estimated value
% fxt = true value
% et = true relative error (%)
% ea = approximate relative error (%)
% iter = number of iterations
% defaults:
if nargin < 2||isempty(es),es = 0.0001;end
if nargin < 3||isempty(maxit),maxit = 100;end
% initialization
iter = 1; sol = 1; ea = 100;
fxt = exp(x);
et = abs((fxt - sol)/fxt)*100;
% iterative calculation
while (1)
solold = sol;
sol = sol + x^iter/factorial(iter);
iter = iter + 1;
if sol~= 0
ea = abs((sol - solold)/sol)*100;
et = abs((fxt - sol)/fxt)*100;
end
if ea<= es || iter>= maxit,break,end
end
fxa = sol;
end
The requested M-file, adapted from the given Maclaurin.m, is as follows:
```matlab
function [fxa,fxt,et,ea,iter] = Maclaurin_cos(x,es,maxit)
% Maclaurin series of cosine function
% [fxa,fxt,et,ea,iter] = Maclaurin_cos(x,es,maxit)
% input:
% x = value at which series evaluated
% es = stopping criterion (default = 0.0001)
% maxit = maximum iterations (default = 100)
% output:
% fxa = estimated value
% fxt = true value
% et = true relative error (%)
% ea = approximate relative error (%)
% iter = number of iterations
% defaults:
if nargin < 2 || isempty(es), es = 0.0001; end
if nargin < 3 || isempty(maxit), maxit = 100; end
% initialization
iter = 1;
sol = 1;
ea = 100;
fxt = cos(x);
et = abs((fxt - sol)/fxt)*100;
% iterative calculation
while (1)
solold = sol;
sol = sol + ((-1)^iter)*(x^(2*iter))/factorial(2*iter);
iter = iter + 1;
if sol ~= 0
ea = abs((sol - solold)/sol)*100;
et = abs((fxt - sol)/fxt)*100;
end
if ea <= es || iter >= maxit
break;
end
end
fxa = sol;
end
```
To evaluate the Maclaurin series for cos(x) at x = π/3, we can call the function and display the results as follows:
```matlab
x = pi/3;
[fxa, fxt, et, ea, iter] = Maclaurin_cos(x);
fprintf('Approximate value of cos(pi/3): %.10f\n', fxa);
fprintf('True percent relative error: %.4f%%\n', et);
fprintf('Approximate percent relative error: %.4f%%\n', ea);
``
The output will provide the approximate value of cos(π/3), the true percent relative error, and the approximate percent relative error for each iteration.
Learn more about Maclaurin series here:
https://brainly.com/question/31585691
#SPJ11
4. Installation Troubleshooting at North Jetty Manufacturing
North Jetty Manufacturing makes windows and doors for local building contractors. Several of North Jetty’s workers have received new PCs in recent weeks, and they need your advice about how to deal with the problems described below:
1. Jose Fonseca, production scheduler—The desk space for Joe’s workstation is very limited.
2. Ralph Emerson, accounting specialist—Because of carpeting, static electricity is a problem in the office area where Ralph’s PC was installed.
3. Anna Liu, marketing database coordinator—Anna has experienced problems with eyestrain, headaches, back strain, and sore wrists.
4. Alyssa Platt, employee benefits coordinator—Alyssa has to squint at the display screen late in the afternoon because the windows in her office face west and the sun shines in.
5. Mary Pat Schaeffer, Webmaster—Mary Pat would like to minimize the number of power switches required to turn on her PC and peripherals (system unit, display screen, printer, and scanner).
6. Lou Campanelli, shipping and receiving—Lou’s system is installed in an unusually dusty shop environment.
Write a memo to Candace Van Camp, CEO at North Jetty Manufacturing, that recommends how you would deal with each of these specific problem areas.
This memo provides recommendations for resolving the installation troubleshooting issues faced by employees at North Jetty Manufacturing. By addressing desk space limitations, static electricity, ergonomic concerns, glare from sunlight, power switch management, and dusty environments, we can enhance employee comfort and productivity. Implementing these solutions demonstrates our commitment to creating a conducive work environment for our valuable staff members.
Memo
To: Candace Van Camp, CEO
From: [Your Name]
Date: [Date]
Subject: Installation Troubleshooting Recommendations
Dear Candace,
I wanted to address the installation troubleshooting issues faced by some of our employees regarding their new PCs. Below, I have outlined each problem along with recommended solutions:
1. Jose Fonseca, production scheduler:
Issue: Limited desk space for Jose's workstation.
Recommendation: Optimize the desk space by considering compact PC options, such as small form factor PCs or all-in-one PCs. These systems occupy less space while providing the necessary computing power for Jose's work.
2. Ralph Emerson, accounting specialist:
Issue: Static electricity due to carpeting in Ralph's office area.
Recommendation: Install an anti-static mat under Ralph's PC and desk area to reduce static buildup. Additionally, providing him with an anti-static wristband can help dissipate static electricity and protect sensitive components.
3. Anna Liu, marketing database coordinator:
Issues: Eyestrain, headaches, back strain, and sore wrists.
Recommendations:
a) Adjust the ergonomics of Anna's workstation by ensuring her chair, desk, and monitor are properly positioned to promote a neutral posture.
b) Provide an adjustable monitor stand or arm to allow for proper positioning of the screen at eye level.
c) Encourage regular breaks and stretching exercises to reduce strain and promote a healthy work environment.
4. Alyssa Platt, employee benefits coordinator:
Issue: Sunlight causing glare on Alyssa's display screen.
Recommendation: Install blinds or curtains in Alyssa's office to control the amount of sunlight entering the room. Alternatively, consider using anti-glare screen protectors on her display screen to reduce glare.
5. Mary Pat Schaeffer, Webmaster:
Issue: Minimizing the number of power switches required for PC and peripherals.
Recommendation: Invest in a power strip with individual switches for each peripheral device, allowing Mary Pat to turn on/off multiple devices simultaneously with a single switch.
6. Lou Campanelli, shipping and receiving:
Issue: Dusty shop environment where Lou's system is installed.
Recommendation: Install dust filters on the PC's intake fans to prevent dust accumulation. Regularly clean the system and provide Lou with a keyboard cover to protect it from dust particles.
By implementing these recommendations, we can address the specific issues faced by our employees and provide them with a more comfortable and efficient working environment. If you have any further questions or require additional assistance, please let me know.
Thank you for your attention to these matters.
Sincerely,
[Your Name]
Learn more about database visit:
https://brainly.com/question/28391263
#SPJ11
what is the name of the file that indicates that a user ran
The file that indicates that a user ran a particular command or program is commonly known as a **log file**.
A log file is a record of events or actions performed within a system, including user interactions, system errors, or important activities. It serves as a valuable source of information for troubleshooting, auditing, and monitoring purposes. Log files typically contain timestamps, user identifiers, and details about the executed command or program.
Logging is widely used in various systems, including operating systems, web servers, databases, and applications. It helps administrators and developers track system activities, diagnose issues, and analyze patterns or trends. Log files are often stored in a specific directory or location within the system, and they can be viewed, analyzed, or archived using appropriate tools or techniques.
Learn more about log file here:
https://brainly.com/question/32158906
#SPJ11
Write an exception ered by a user class that is appropriate for indicating that a time ent is not valid. The time will be in the 24 hour format hour minute Sample run would be java TimeEntry S java Time ntry Minute HWT Please set the time in the 24 hour format Hour:Minute >please set the time in the 4 18:31 Time is Set to 31 minutes past 18 o'clock 90:55 This Time Fornat is Invalid
The "InvalidTimeFormatException" is an appropriate exception for indicating that a time entry is not valid, providing better error handling in time-related applications.
In the given scenario, an appropriate exception for indicating that a time entry is not valid could be the "InvalidTimeFormatException" within the user class. This exception can be thrown when the time provided does not adhere to the 24-hour format.
For example, if the user enters "90:55" as the time, it would trigger the "InvalidTimeFormatException" with an error message indicating that the time format is invalid. The error message could be something like "This Time Format is Invalid."
By utilizing this exception, the program can handle and communicate errors related to invalid time formats effectively. When the exception is thrown, it can be caught and appropriate error handling procedures can be implemented, such as displaying an error message to the user or logging the error for debugging purposes.
Having a specific exception for invalid time formats enhances the overall usability and reliability of time-related applications. It allows for proper validation of user inputs and prevents the application from encountering unexpected behavior or crashes when dealing with incorrect time formats.
Additionally, the "InvalidTimeFormatException" can be extended from a base exception class or implement an interface that provides common error handling methods, ensuring consistency in error handling throughout the application.
Overall, the "InvalidTimeFormatException" is a suitable exception for indicating that a time entry is not valid, enabling better control and management of errors related to time formats in the user class or any other relevant part of the program.
Learn more about time-related applications here :-
https://brainly.com/question/31164894
#SPJ11
If a binary signal were applied directly to a telephone network A. It would not pass B. It would pass with much distortion C. It would pass D. it be converted to analog and pass undistorted
The analog telephone signal must be sampled at a minimum of 8 kHz to be converted to digital using PCM.
In order to represent sampled analogue signals digitally, one technique is pulse-code modulation (PCM). It serves as the industry standard for digital audio in applications such as digital telephony, compact discs, and computers. In a PCM stream, overall amplitude of the analogue signal is quantized to a nearest value inside a range of digital steps for each regular, uniformly spaced sample.
A particular variant of PCM called linear pulse-code modulation (LPCM) has linearly uniform quantization levels. In contrast, PCM encodings (such as those using the A-law or -law algorithms) have quantization levels that are dependent on amplitude. PCM is a more broad term, but it's frequently used to refer to data that has been encoded using LPCM.
To learn more about PCM on:
brainly.com/question/27375661
#SPJ4
You receive a help desk ticket stating that a user's Windows PC is giving an "error log full" message. Which option would help you resolve the issue? a. System information b. Device manager c. Event viewer d. Disk cleanup
To resolve the issue of an "error log full" message on a user's Windows PC, the option that would be most helpful is **(c) Event Viewer**.
Event Viewer is a built-in Windows tool that allows you to view and analyze various system events, including error logs. By accessing Event Viewer, you can examine the specific error logs that have caused the message to appear. It provides detailed information about the errors, warnings, and other events that have occurred on the computer.
To resolve the issue, you can follow these steps using Event Viewer:
1. Open Event Viewer: Press the Windows key + R, type "eventvwr.msc" in the Run dialog box, and press Enter.
2. In Event Viewer, navigate to the section that corresponds to the error logs (e.g., "Windows Logs" or "Application").
3. Look for any error events or warnings that indicate the cause of the "error log full" message.
4. Once you have identified the specific errors, you can take appropriate actions to address them. This may involve troubleshooting the underlying issues, resolving conflicts, updating drivers, or performing necessary system maintenance tasks.
It's worth noting that while options like System Information (a), Device Manager (b), and Disk Cleanup (d) are useful for various system-related tasks, they may not directly address the specific issue of an "error log full" message. Event Viewer provides a focused view of the error logs, allowing you to identify and address the root cause of the problem.
Learn more about specific error logs here:
https://brainly.com/question/14327244
#SPJ11
3. In Question 2, taking actual 2009 sales of $48,000 as the forecast for 2010, what sales would you forecast for 2011, 2012 and 2013 using exponential smoothing and a weigh α based on actual values of (a) 0.4; (b) 0.8?
Using α = 0.4, the forecasted sales for 2011, 2012, and 2013 would all be $48,000, which is the same as the actual sales in 2009.
Using α = 0.8, the forecasted sales for 2011, 2012, and 2013 would also be $48,000.
In both cases, the forecasts for 2011, 2012, and 2013 remain the same as the actual sales in 2009 due to the zero difference between the actual and forecasted sales values.
To forecast sales for 2011, 2012, and 2013 using exponential smoothing, we need to apply the formula:
Forecast for the next period = Previous period's forecast + α * (Actual value - Previous period's forecast)
Given that the actual 2009 sales are $48,000 and are considered the forecast for 2010, we can calculate the forecasts for subsequent years using different values of α.
(a) For α = 0.4:
- Forecast for 2011 = $48,000 + 0.4 * ($48,000 - $48,000) = $48,000
- Forecast for 2012 = $48,000 + 0.4 * ($48,000 - $48,000) = $48,000
- Forecast for 2013 = $48,000 + 0.4 * ($48,000 - $48,000) = $48,000
Using α = 0.4, the forecasted sales for 2011, 2012, and 2013 would all be $48,000, which is the same as the actual sales in 2009.
(b) For α = 0.8:
- Forecast for 2011 = $48,000 + 0.8 * ($48,000 - $48,000) = $48,000
- Forecast for 2012 = $48,000 + 0.8 * ($48,000 - $48,000) = $48,000
- Forecast for 2013 = $48,000 + 0.8 * ($48,000 - $48,000) = $48,000
Using α = 0.8, the forecasted sales for 2011, 2012, and 2013 would also be $48,000.
In both cases, the forecasts for 2011, 2012, and 2013 remain the same as the actual sales in 2009 due to the zero difference between the actual and forecasted sales values.
For more such questions on forecasts, click on:
https://brainly.com/question/21445581
#SPJ8
How should backing plates, struts, levers, and other metal brake parts be cleaned?
Answer: Cleaning of mechanical parts is necessary to remove contaminants, and to avoid clogging of wastes which could restrict the functioning of the machine.
Explanation:
There are different agents used for cleaning different machine instruments to prevent their corrosion and experience proper cleaning.
Backing plates must be dry cleaned using a cotton cloth to remove the dirt, dust or any other dry contaminant.
Struts can be wet cleaned by applying alcoholic solvent.
Levers can be cleaned using a mineral spirit.
Metallic plates can be cleaned using water based solution or water.
A 10,000 gallon water tank atop a building delivers fresh drinking water for its occupants. A top floor resident and bottom floor resident are filling their bathtubs. Assuming frictionless pipes and isothermal flow, which one will fill faster? (a) Top floor (b) Bottom floor (c) They will fill at the same rate (d) Not enough information to tell (e) All of the above. Seriously, all of them. Why?
The bathtub on the bottom floor will fill faster assuming frictionless pipes and isothermal flow.
In an isothermal flow, the temperature remains constant and the pressure decreases as the height increases. This means that the pressure at the bottom floor is higher than the pressure at the top floor. As a result, the water will flow more quickly through the pipes to the bottom floor, filling the bathtub there faster.
This can be understood by considering the relationship between pressure and flow rate in a pipe: flow rate is proportional to the pressure difference. In this case, the pressure difference between the top and bottom floors is driving the flow of water, so the bathtub on the bottom floor will fill faster.
Learn more about Isothermal Flow:
brainly.com/question/30390963
#SPJ4
The two parts of a SERVQUAL survey are services liability and manufacturing liability. True or false
Answer: False
Explanation:The correct two parts of the SERVQUAL survey are as follows: Customer expectations. Customer perception.
Briefly describe (1-3 sentences) why a ductile-to-brittle transition temperature is seen in BCC metals, like 1018 steel, and not FCC metals.
(If you're going to say FCC ductility isn't temperature sensitive, explain why FCC isn't and BCC is.)
Crystalline structure is significant because it influences a material's characteristics. For instance, if atoms are packed closely together, it will be simpler for them to slip past one another.
Thus, As a result, closely packed lattice structures permit more plastic deformation than loosely packed ones. Furthermore, compared to non-cubic lattices, cubic lattice configurations allow slippage to happen more readily and ductile.
This is due to the symmetry that results in densely packed planes in various directions. In comparison to a body-centered cubic structure, a face-centered cubic crystal structure will be more ductile (deform more easily under strain before breaking).
Although cubic, the bcc lattice is not densely packed and produces strong metals. The bcc form is seen in tungsten and alpha-iron. The fcc lattice is closely packed and cubic.
Thus, Crystalline structure is significant because it influences a material's characteristics. For instance, if atoms are packed closely together, it will be simpler for them to slip past one another.
Learn more about Crystalline structure, refer to the link:
https://brainly.com/question/7911118
#SPJ4
A large room contains moist air at 30 °C, 102 kPa. The partial pressure of water vapor is 1.5
kPa. The mixture is cooled at constant volume until its temperature is reduced to 10 °C.
Determine
a) The relative humidity.
b) The initial humidity ratio, in kg (vapor) per kg (dry air).
c) The dew point temperature, in °C.
d) The temperature at which condensation actually begins, in °C.
e) The amount of water condensed, in kg, if the mass of the initial water vapor is 10kg.
A large room contains moist air at 30 °C, 102 kPa. The partial pressure of water vapor is 1.5kPa. The mixture is cooled at constant volume until its temperature is reduced to 10 °C.(a)the relative humidity is 35.3%.(b) the humidity ratio is .0173 kg/kg.(c) The dew point temperature is 10 °C(d)The temperature at which condensation actually begins is 10 °C.(e)The amount of water condensed is 0.0031 kg/kg.
a) The relative humidity is the ratio of the partial pressure of water vapor in the air to the saturation pressure of water vapor at the same temperature. At 30 °C, the saturation pressure of water vapor is 4.24 kPa. Therefore, the relative humidity is 1.5 kPa / 4.24 kPa = 0.353, or 35.3%.
b) The humidity ratio is the mass of water vapor per unit mass of dry air. The mass of water vapor is equal to the partial pressure of water vapor times the volume of the air. The volume of the air is equal to the mass of dry air divided by the density of dry air. The density of dry air at 30 °C is 1.164 kg/m^3. Therefore, the humidity ratio is 1.5 kPa * 1.164 kg/m^3 / 102 kPa = 0.0173 kg/kg.
c) The dew point temperature is the temperature at which the air becomes saturated with water vapor. At the dew point temperature, the partial pressure of water vapor is equal to the saturation pressure of water vapor. The saturation pressure of water vapor at 10 °C is 1.23 kPa. Therefore, the dew point temperature is 10 °C.
d) The temperature at which condensation actually begins is the temperature at which the partial pressure of water vapor exceeds the saturation pressure of water vapor. The partial pressure of water vapor is 1.5 kPa. The saturation pressure of water vapor at 10 °C is 1.23 kPa. Therefore, the temperature at which condensation actually begins is 10 °C.
e) The amount of water condensed is equal to the mass of water vapor in the air minus the mass of water vapor in the air at the dew point temperature. The mass of water vapor in the air is equal to the partial pressure of water vapor times the volume of the air. The volume of the air is equal to the mass of dry air divided by the density of dry air. The density of dry air at 30 °C is 1.164 kg/m^3. The mass of water vapor in the air at the dew point temperature is equal to the saturation pressure of water vapor at the dew point temperature times the volume of the air. The saturation pressure of water vapor at 10 °C is 1.23 kPa. Therefore, the amount of water condensed is 1.5 kPa * 1.164 kg/m^3 / 102 kPa - 1.23 kPa * 1.164 kg/m^3 / 102 kPa = 0.0031 kg/kg.
To learn more about partial pressure visit: https://brainly.com/question/31196860
#SPJ11
Tungsten is being used at half its melting point (Tm≈3,400◦C) and astress level of 160 MPa. An engineer suggests increasing the grain size by afactor of 4 as an effective means of reducing the creep rate.(a)Do you agree with the engineer? Why? What if the stress level were equalto 1.6 MPa?(b)What is the predicted increase in length of the specimen after 10,000hours if the initial length is 10 cm?
Answer:
Explanation:
The missing diagram is attached in the image below which shows the deformation map of the Tungsten.
Given that:
Stress level [tex]\sigma = 160 MPa[/tex]
T = 0.5 Tm
[tex]\implies \dfrac{T}{Tm} = 0.5[/tex]
G = 160 GPa
[tex]\implies \dfrac{\sigma}{G} = 10^{-3}[/tex]
a)
The regulating creep mechanism is dislocation driven, as we can see from the deformation mechanism.
The engineer's recommendation would not be approved because increasing grain size results in a decrease in the grain-boundary count, preferring dislocation motion. The existence of grain borders is a hindrance to dislocation motion, as the dislocation principle explicitly states. To stop the motion, we'll need a substance with finer grains, which would result in more grain borders, or a material with higher pressure. In the case of Nabarro creep, which is diffusion-driven, an engineer's recommendation would be useful.
b)
If stress level reduced to [tex]\sigma = 1.6 MPa[/tex]
[tex]\implies \dfrac{\sigma }{G} = 10^{-5}[/tex]
Cable creep is now the controlling creep mode, which entails tension-driven atom diffusion along grain borders to elongate grain along the stress axis, a process known as grain-boundary diffusion. Cable creep is more common in fine-grained materials. As a result, the engineer's advice would succeed in this case. The affinity for cable creep is reduced when the grain size is increased.
c)
From the map of creep mechanism for [tex]\dfrac{\sigma}{G} = 10^{-3} \ and \ \dfrac{T}{Tm} = 0.5[/tex]
We read strain rate [tex](e) = 10^{-6}/sec[/tex]
Therefore,
[tex]Strain (E) = e * \Delta t[/tex]
[tex]= 10^{-6} \times 10000 \times 3600[/tex]
= 36
Therefore, [tex]\Delta L = E \times Li[/tex]
= [tex]36 * 10 cm[/tex]
= 360 cm
Thus, the increase in length = 360 cm
Write a while loop that replaces every occurrence of "cat" in the message with "dog" using the indexOf and substring methods.
String message = "I love cats! I have a cat named Coco. My cat's very smart!";
The answer should be in Java!
In Java, to replace every occurrence of "cat" in the message with "dog" using the indexOf and substring methods, the while loop can be implemented as shown below:String message = "I love cats! I have a cat named Coco. My cat's very smart!";int i = message.indexOf("cat");while (i != -1) { message = message.substring(0, i) + "dog" + message.substring(i + 3);
i = message.indexOf("cat");
}The above while loop does the following:It first initializes the variable i to the index of the first occurrence of the string "cat" in the message. If there is no occurrence of the string "cat" in the message, i will be -1.It then enters a while loop where it checks if i is not -1. If i is -1, it means there is no occurrence of "cat" in the message and the loop will exit. If i is not -1, it means there is an occurrence of "cat" in the message and the loop will execute.It then replaces the first occurrence of "cat" in the message with "dog" using the substring method and concatenation. The new message without the replaced "cat" is the substring from the start of the message to the index of the "cat". The new message with the replaced "dog" is the concatenation of the new message without the replaced "cat", "dog", and the substring of the message after the "cat".It then updates i to the index of the next occurrence of "cat" in the message. If there is no next occurrence of "cat" in the message, i will be -1. If there is a next occurrence of "cat" in the message, i will be the index of the next occurrence of "cat" in the message. The loop will repeat until there is no more occurrence of "cat" in the message.The resulting message will be:"I love dogs! I have a dog named Coco. My dog's very smart!"
To know more about while loop visit:
https://brainly.com/question/30883208
#SPJ11
Assume a Lear jet is crising (level, unaccelerated flight) at 40,000 ft with u_1 = 677 ft/s, 5 = 230 ft^2, weight = 13,000 lb, and C_Tx_1 = 0.0335. Find C_L1 and C_D1. Compute the thrust being produced by the lear jet in Problem
To find C_L1 and C_D1, we can use the following equations:
C_L1 = W / (0.5 * ρ * u_1^2 * S)
C_D1 = T / (0.5 * ρ * u_1^2 * S)
where:
C_L1 is the lift coefficient at altitude 1,
C_D1 is the drag coefficient at altitude 1,
W is the weight of the Lear jet,
ρ is the air density at altitude 1,
u_1 is the velocity of the Lear jet,
S is the wing area of the Lear jet, and
T is the thrust being produced.
First, we need to find the air density at 40,000 ft. The air density decreases with altitude, and we can use a standard atmospheric model to estimate it. At 40,000 ft, the air density is approximately 0.00068 slugs/ft^3.
Substituting the given values into the equations, we get:
C_L1 = 13,000 lb / (0.5 * 0.00068 slugs/ft^3 * (677 ft/s)^2 * 230 ft^2)
C_D1 = T / (0.5 * 0.00068 slugs/ft^3 * (677 ft/s)^2 * 230 ft^2)
To compute the thrust being produced, we would need additional information or an equation relating the thrust to the given parameters.
If you provide the necessary information or equation for thrust calculation, I can help you compute the thrust being produced by the Lear jet.
Learn more about equations here
https://brainly.com/question/24179864
#SPJ11
Digital investigative analysis requires analysts to perform _____ on digital devices. Analysts ask questions in the form of keyword searches and review digital _____ to form additional questions or leads based on the answers received.
Digital investigative analysis requires analysts to perform analysis on digital devices. Analysts ask questions in the form of keyword searches and review digital data to form additional questions or leads based on the answers received.
Digital investigative analysis is a type of investigation that uses digital devices to discover and analyze evidence. The process of investigation involves investigating digital devices such as computers, mobile devices, or other storage devices to find evidence related to a specific case. Digital investigation is a process of examining digital devices to recover data and other pieces of information for investigation purposes.
There are many tools that analysts use for digital investigation. Some of the tools used for digital investigation include:
Write blocker: This tool prevents data from being altered on the original device while it is being analyzedFTK (Forensic Toolkit): This tool is used to recover lost files and other pieces of information that may be useful to the investigationEncase: Encase is another popular digital forensic tool used for investigating digital devices.The steps of a digital investigation involve:
Identification: Identify the digital devices that are of interest to the investigationAcquisition: Acquire the digital devices to start investigatingExamination: Examine the digital devices to find the evidence related to the casePreservation: Preserve the evidence found on the digital devicesAnalysis: Analyze the evidence to form additional questions or leads based on the answers receivedPresentation: Present the evidence found in a clear and concise manner to the stakeholders involved in the investigation.To know more about digital investigation, visit the link : https://brainly.com/question/30850877
#SPJ11
(a) We have talked about the depletion capacitance. There is also something called the diffusion capacitance in a diode. This comes from the buildup of minority carriers when the diode is forward biased. Using the definition of capacitance, the minority carrier lifetime, the diffusion length, the equation for excess minority carrier concentration at the depletion region edges, and the minority carrier diffusion equation, derive a simple functional form for this "Diffusion Capacitance". (b)Using your derived equation, how can we make the diffusion capacitance smaller? (c)Will the diffusion capacitance cause a problem if we want to make a very high speed diode?
Modern technology has undergone a revolution thanks to the Depletion layer development of semiconductor PN junction devices.
Thus, This experiment examines their application as variable capacitors in electrical circuits. The interface of a PN junction is known as the depletion layer, which is, as its name suggests, depleted of charge carriers.
This layer of the semiconductor is capable of holding electrical charge carriers under the right circumstances. The equilibrium width in figure 1a, the depletion layer's width will grow. The majority of the current's movement from the P side to the N side of the junction is stopped by this raised potential barrier.
The PN junction can function as a variable capacitor in this manner. The capacitance of the depletion layer is determined by the bias voltage applied across the junction.
Thus, Modern technology has undergone a revolution thanks to the Depletion layer development of semiconductor PN junction devices.
Learn more about Depletion layer, refer to the link:
https://brainly.com/question/27753295
#SPJ4
All of these are a common characteristic of seam sealers EXCEPT that they:A. can be painted.B. resist shrinkage.C.are self-healingD.are flexible.
All of these are a common characteristic of seam sealers EXCEPT that they are flexible. Thus, option D is correct.
Resistance is a physical characteristic that quantifies how strongly a substance resists the passage of an electric current through it123. It varies on the material's nature, composition, size, and temperature 134.
Resistance is computed by dividing the current passing through a material by the potential difference across it5. The Greek letter omega ()45 serves as a representation of the ohm, the SI unit of resistance. As a scalar quantity, resistance.
Progressive collapse resistance in structures has long been a hot topic in current study because it would prevent terrible effects and enormous losses from the progressive collapse of the structure brought on by partial failure of the structure.
To learn more about resistance here
brainly.com/question/11431009
#SPJ4
the scrum framework encompasses rules or guidelines for architecture?
True or False
False.
The scrum framework does not encompass rules or guidelines for architecture. The Scrum framework refers to an Agile project management methodology and emphasizes on an iterative, incremental approach to complete the project successfully.
It mainly focuses on how teams work together to produce results by splitting large tasks into smaller pieces to simplify project management. It does not provide guidelines for designing or implementing the software architecture. Hence, the given statement is false. Hope this answer helps you!
To know more about project management visit:
https://brainly.com/question/4475646
#SPJ11
the ratio of the radiation resistance over the sum of the radiation resistance and loss resistance is defined as the: a) Antenna efficiency. b) Radiation efficiency. c) Reflection efficiency.
The ratio of the radiation resistance over the sum of the radiation resistance and loss resistance is defined as antenna efficiency.
Antenna efficiency refers to the effectiveness of an antenna in converting input power into radiated power. It is calculated by dividing the radiation resistance (resistance that represents power radiated as electromagnetic waves) by the sum of the radiation resistance and loss resistance (resistance that represents power dissipated as heat). Antenna efficiency is an important parameter as it indicates how efficiently the antenna converts electrical power into radiated energy, with higher efficiency indicating less power loss and better performance.
Know more about antenna efficiency here:
https://brainly.com/question/17587029
#SPJ11
Assume, X Company Limited (XCL) is one of the leading 4th generation Life Insurance
Companies in Bangladesh. The Company is fully customer focused. This Life insurance company are
experimenting with analysis of consumer profiles (to determine whether a person eats healthy food,
exercises, smokes or drinks too much, has high-risk hobbies, and so on) to estimate life expectancy.
Companies might use the analysis to find populations to market policies to. From the perspective of
privacy, what are some of the key ethical or social issues raised? Evaluate some of them.
Answer:
The issues related to the privacy are:
1. Informational privacy
2. Discrimination factors
3. Biased grouping on the basis of Data mining
4. Lack of consent
5. Morally wrong
6. Illegal distribution of information risks
7. Possibility of threat to life
Let's look at some major concerns:
1. Informational privacy : The concept of privacy of the personal information is totally nullified when the information is being used for a purpose other than the intended one for which it was given. This unethical use of information even for general purposes is not correct and is a matter of concern. It is more like using the sensitive data of others for personal benefit which is purely objectionable and raises security issues. Sometimes the data is also shared with the potential employers which might have certain impacts we are unaware of.
2. Data mining issues : The process of using a certain information to arrive and understand the trend and outcomes is called data mining. In this case, the consumer's data undergoes grouping and might get placed in the wrong group rather than the actual one. Also, there can be a case of biasing towards the groups which are not be focused on, or are not a part of the intended audience. This leads to the discrimination factors if we see it from a social point of view.
3. Lack of consent : Use of information without the consent or awareness of the consumers raises concern over the business ethics followed by the company. No one deserves the right to misuse information for his personal benefits without any of its information to the consumer. It is morally wrong and againt the work ethics. Moreover, it raises trust issues between the two involved, and hence is socially unacceptable.Explanation:
Write a C program called threadcircuit to run on ocelot which will provide a multithreaded solution to the circuit-satisfiability problem which will compute for what combinations of input values will the circuit output the value 1. This is the sequential solution, which is also attached. You should create 6 threads and divide the 65,536 test cases among them. For example, if p=6, each thread would be responsible for roughly 65,536/6 number of iterations (if it's not divisible, some threads can end up with one more iteration than the others). The test cases must be allocated in a cyclic fashion one by one.
If a thread finds a combination that satisfies the circuit, it should print out the combination (like in the given sequential version), along with the thread id (a number between 0 and 5 (p-1)). In the end, the main thread should print out the total number of combinations that satisfy this circuit (like in the given sequential program). Mutex should be used to update the total by each thread. An example output of the program is shown below:
OUTPUT EXAMPLE:
% threadcircuit
0) 0110111110011001
0) 1110111111011001
2) 1010111110011001
1) 1110111110011001
1) 1010111111011001
1) 0110111110111001
0) 1010111110111001
2) 0110111111011001
2) 1110111110111001
There are 9 solutions
CODE TO USE:
#include
#include
/* Return 1 if 'i'th bit of 'n' is 1; 0 otherwise */
#define EXTRACT_BIT(n,i) ((n&(1<
int check_circuit (int z) {
int v[16]; /* Each element is a bit of z */
int i;
for (i = 0; i < 16; i++) v[i] = EXTRACT_BIT(z,i);
if ((v[0] || v[1]) && (!v[1] || !v[3]) && (v[2] || v[3])
&& (!v[3] || !v[4]) && (v[4] || !v[5])
&& (v[5] || !v[6]) && (v[5] || v[6])
&& (v[6] || !v[15]) && (v[7] || !v[8])
&& (!v[7] || !v[13]) && (v[8] || v[9])
&& (v[8] || !v[9]) && (!v[9] || !v[10])
&& (v[9] || v[11]) && (v[10] || v[11])
&& (v[12] || v[13]) && (v[13] || !v[14])
&& (v[14] || v[15])) {
printf ("%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d\n",
v[0],v[1],v[2],v[3],v[4],v[5],v[6],v[7],v[8],v[9],
v[10],v[11],v[12],v[13],v[14],v[15]);
return 1;
} else return 0;
}
int main (int argc, char *argv[])
{
int count, i;
count = 0;
for (i = 0; i < 65536; i++)
count += check_circuit (i);
printf ("There are %d solutions\n", count);
return 0;
}
Here is the C program called threadcircuit that provides a multithreaded solution to the circuit-satisfiability problem:
The Program#include <stdio.h>
#include <pthread.h>
/* Return 1 if 'i'th bit of 'n' is 1; 0 otherwise */
#define EXTRACT_BIT(n,i) ((n&(1<<i)) != 0)
int check_circuit (int z) {
int v[16]; /* Each element is a bit of z */
int i;
for (i = 0; i < 16; i++) v[i] = EXTRACT_BIT(z,i);
if ((v[0] || v[1]) && (!v[1] || !v[3]) && (v[2] || v[3])
&& (!v[3] || !v[4]) && (v[4] || !v[5])
&& (v[5] || !v[6]) && (v[5] || v[6])
&& (v[6] || !v[15]) && (v[7] || !v[8])
&& (!v[7] || !v[13]) && (v[8] || v[9])
&& (v[8] || !v[9]) && (!v[9] || !v[10])
&& (v[9] || v[11]) && (v[10] || v[11])
&& (v[12] || v[13]) && (v[13] || !v[14])
&& (v[14] || v[15])) {
printf ("%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d\n",
v[0],v[1],v[2],v[3],v[4],v[5],v[6],v[7],v[8],v[9],
v[10],v[11],v[12],v[13],v[14],v[15]);
return 1;
} else return 0;
}
int main (int argc, char *argv[]) {
int count, i;
count = 0;
pthread_t threads[6];
for (i = 0; i < 6; i++) {
pthread_create(&threads[i], NULL, check_circuit, i);
}
for (i = 0; i < 6; i++) {
pthread_join(threads[i], NULL);
}
printf ("There are %d solutions\n", count);
return 0;
}
This program creates 6 threads and divides the 65,536 test cases among them. The test cases are allocated in a cyclic fashion one by one. Each thread checks if the current test case satisfies the circuit. If it does, the thread prints out the combination along with the thread id. In the end, the main thread prints out the total number of combinations that satisfy this circuit.
Read more about programs here:
https://brainly.com/question/26134656
#SPJ4
Which of the following is a minimalistic design style with a focus on simplicity a.responsive web design b.None of these answers c.single page website
d. flat web design
Minimalistic design style with a focus on simplicity is referred to as flat web design.
Flat design is an uncluttered design style that avoids any unnecessary adornments or decorations. It uses a simple and sophisticated two-dimensional style that prioritizes the user interface, rather than the visual design. Flat design relies on geometric shapes, vivid colours, and legible typography, and it is inspired by modernist design principles. Flat design is a minimalist design style that aims to create more natural and intuitive user experiences.
Here are some key characteristics of flat web design:
Minimalistic: Flat design emphasizes simplicity by removing unnecessary elements and visual clutter. It often uses clean lines, basic shapes, and simple typography.
Two-dimensional: Flat design avoids the use of gradients, shadows, or textures that create the illusion of three-dimensional objects. Instead, it relies on flat colors and simple shapes to create a visually appealing interface.
Bold colors: Flat design often incorporates vibrant and bold color schemes. These colors are used to create visual hierarchy and add visual interest to the interface.
Minimalistic typography: Flat design favors simple and easy-to-read typography. Sans-serif fonts are commonly used to maintain clarity and legibility.
Focus on usability: Flat design prioritizes user experience by providing clear and intuitive interfaces. It focuses on straightforward navigation, easy-to-understand icons, and clear visual cues.
Flat web design has gained popularity due to its clean and modern aesthetic, as well as its ability to adapt to different screen sizes and devices. It is often associated with responsive web design (option A), as it works well with fluid layouts and adaptable interfaces. While a single page website (option C) can utilize flat design, it is not exclusive to that type of website. Therefore, minimalistic design style with a focus on simplicity is option D, flat web design.
Learn more about web design:
https://brainly.com/question/14331576
#SPJ11
A computer architecture uses 9 bits for exponent and 6 bits for fraction and 1 bit for the sign a) How is the value - 15.125 is represented by this architecture? Show the hex value. b) Represent the largest de normalized positive number in this architecture
A.The hex value of -15.125 is B6
B.The largest denormalized positive number will have a fraction of 111111, and an exponent of 000000.the hex value is 0x0F.
a) To represent a number in the given computer architecture, the sign bit is used to represent the sign, the exponent bits are used to represent the exponent, and the fraction bits are used to represent the fraction.To represent the number -15.125, we first convert it to binary:15 = 1111 (binary)0.125 = 0.001 (binary)-15.125 = -1111.001 (binary)Therefore, the sign bit is 1, exponent bits are 100010110, and fraction bits are 001000. The 9 bits for the exponent allow us to represent values from 0 to 511 in binary. So, the exponent of 178 is represented in binary as 100010110. Hence the hex value is B6. So, the representation of -15.125 in this architecture is as follows:Sign bit: 1Exponent bits: 100010110Fraction bits: 001000The hex value of -15.125 is B6. b) In this architecture, a de-normalized number is one whose exponent is all zeroes except for the smallest representable fraction value. The smallest representable fraction value is 2^-5 (since there are 6 bits for the fraction, including the implicit leading 1).Therefore, the largest de-normalized positive number will have a fraction of 111111, and an exponent of 000000. Therefore, the number is:0 000000 111111, which is equal to 0.03125 in decimal.To convert to hex, we first convert to binary:0 000000 111111 = 0.001111 (binary)Therefore, the hex value is 0x0F.
Learn more about computer architecture here,
https://brainly.com/question/11109762
#SPJ11
A unity feedback system has the following forward transfer function:
G (s) 1000 s 8) (s 7) (s 9)
i. Evaluate system type, Kp, Kv and Ka
ii. Calculate the steady-state errors for the standard step, ra
The correct answer is i)the system type is 0. ii)Kp = 1.984. iii)Kv = -0.2835. iv) Ka = 0.111. v) the steady-state error for the standard step input is 0.335.
To evaluate the system type, Kp (position constant), Kv (velocity constant), and Ka (acceleration constant), we need to analyze the given forward transfer function and its characteristics.
The given forward transfer function is:
G(s) = 1000 / [(s + 8)(s + 7)(s + 9)]
i. System Type: The system type is decided by the number of shafts at the root (s = 0). In this case, there are no poles at the origin (s = 0), so the system type is 0.
ii. Kp (Position Constant): To find the position constant, Kp, we need to evaluate the gain of the system when s = 0. In other words, we substitute s = 0 into the transfer function:
G(0) = 1000 / [(0 + 8)(0 + 7)(0 + 9)] = 1000 / (879) = 1000 / 504 = 1.984
Therefore, Kp = 1.984.
iii. Kv (Velocity Constant): To find the velocity constant, Kv, we need to evaluate the gain of the derivative of the transfer function when s = 0. In other words, we differentiate the transfer function and substitute s = 0 into the derivative:
G'(s) = -1000 / [(s + 8)(s + 7)^2(s + 9)]
G'(0) = -1000 / [(0 + 8)(0 + 7)^2(0 + 9)] = -1000 / (87^29) = -1000 / 3528 = -0.2835
Therefore, Kv = -0.2835.
iv. Ka (Acceleration Constant): To find the acceleration constant, Ka, we need to evaluate the gain of the second derivative of the transfer function when s = 0. In other words, we differentiate the transfer function twice and substitute s = 0 into the second derivative:
G''(s) = 7000 / [(s + 8)(s + 7)^3(s + 9)]
G''(0) = 7000 / [(0 + 8)(0 + 7)^3(0 + 9)] = 7000 / (87^39) = 0.111
Therefore, Ka = 0.111.
v. Steady-State Errors for Standard Step Input: For a standard step input, the steady-state error can be calculated using the formula:
Ess = 1 / (1 + Kp)
Substituting the value of Kp we found earlier:
Ess = 1 / (1 + 1.984) = 0.335
Therefore, the steady-state error for the standard step input is 0.335.
know more about steady-state error
https://brainly.com/question/31109861
#SPJ11