Thirty-two bit Media Access Control (MAC) addresses of the source and destination station are added to the packets in a process called encapsulation.
Encapsulation is a process in computer networking where headers, trailers, and other data are added to the original data to create a packet. In this case, MAC addresses of the source and destination station are added to the packet, which is then sent over the network.
The MAC address is a unique identifier assigned to a network interface controller for use as a network address in communications within a network segment. The use of MAC addresses allows the network to identify and deliver packets to specific devices on the network.
You can learn more about MAC (Media Access Control) at
https://brainly.com/question/13842614
#SPJ11
write a program that defines macro minimum2(x,y) using a conditional operator and use this macro to return the smallest of two numerical values. input the values from the keyboard.
The user inputs two integers input the C program, which uses the conditional operator to define minimum2(x, y), and the macro to return the least number.
Here is a C program that uses the conditional operator to define the macro "minimum2(x, y)" and accept keyboard input to return the smaller of two numerical values:
```c
#include
#define minimum2(x, y) ((x) < (y) ? (x) : (y))
int main() {
int value1, value2;
printf("Enter the first value: ");
scanf("%d", &value1);
printf("Enter the second value: ");
scanf("%d", &value2);
int smallest = minimum2(value1, value2);
printf("The smallest value is: %d\n", smallest);
return 0;
}
```
This program accepts the user's two integer inputs, defines the the'minimum2(x, y)' macro using the conditional operator, and then uses the macro to return the smallest number.
learn more about conditional operator here:
https://brainly.com/question/22971481
#SPJ11
Consider a 4-drive, 200 GB-per-drive RAID array. What is the available data storage capacity for each of the RAID levels, 0, 1, 3, 4, 5, and 6? (Note: when talking about the disk storage capacity, the same data replicated physically to two or more disks counts once, not twice or multiple times).
The available data storage capacity for each RAID level can be calculated using the following formulas given below.
What is the RAID array?RAID 0:
Available Capacity = Total Capacity of all drives in the array
RAID 1:
Available Capacity = Total Capacity of a single drive (since data is mirrored across all drives, only one drive's capacity is usable)
RAID 3:
Available Capacity = (Number of Drives - 1) * Capacity of Smallest Drive in the array
RAID 4:
Available Capacity = (Number of Drives - 1) * Capacity of Smallest Drive in the array
RAID 5:
Available Capacity = (Number of Drives - 1) * Capacity of Smallest Drive in the array
RAID 6:
Available Capacity = (Number of Drives - 2) * Capacity of Smallest Drive in the array
Given that you have a 4-drive RAID array with 200 GB-per-drive capacity, the available data storage capacity for each RAID level would be:
RAID 0: 4 * 200 GB = 800 GB
RAID 1: 1 * 200 GB = 200 GB
RAID 3: (4 - 1) * 200 GB = 600 GB
RAID 4: (4 - 1) * 200 GB = 600 GB
RAID 5: (4 - 1) * 200 GB = 600 GB
RAID 6: (4 - 2) * 200 GB = 400 GB
Please note that these calculations are approximate and do not take into account other factors such as overhead, parity, or formatting that may affect the actual usable capacity in a RAID array. It is always recommended to consult the documentation or specifications of your specific RAID controller or system for accurate information on available data storage capacity.
Read more about RAID array here:
https://brainly.com/question/28963056
#SPJ1
What kind of Layer 3 protocols help routers to find routes and help to determine the most efficient of these routes?
Router
Route
routing
routed
Layer 3 protocols such as OSPF, BGP, and EIGRP help routers find and determine the most efficient routes for routing traffic between networks.
OSPF (Open Shortest Path First) is a link-state protocol that uses Dijkstra's algorithm to calculate the shortest path between networks. BGP (Border Gateway Protocol) is a path-vector protocol that determines the best path for traffic between autonomous systems. EIGRP (Enhanced Interior Gateway Routing Protocol) is a hybrid protocol that combines aspects of both distance-vector and link-state protocols to calculate the most efficient route. These protocols allow routers to exchange routing information with each other, build a routing table, and choose the best path for traffic to take based on factors such as network speed, reliability, and cost.
Learn more about networks here:
https://brainly.com/question/29654124
#SPJ11
Write an algorithm that displays the next double message: Enter a month (1 for January, 2 for February,….…) Enter a day of the month
This algorithm prompts the user to enter both the month and day using double messages, and then stores these inputs in separate variables for further processing if needed. Here is the algorithm
Step:1. Start the program.
Step:2. Display the first message: "Enter a month (1 for January, 2 for February, ...)".
Step:3. Accept the user input for the month and store it in a variable called 'month'.
Step:4. Display the second message: "Enter a day of the month".
Step:5. Accept the user input for the day and store it in a variable called 'day'.
Step:6. End the program.
Learn more about algorithm prompts here,
Increase the cohesion of the following class by splitting into two or more classes, and add the mutators, accessors, member variables, and constructors.
public class CashRegister
{
public void enterPayment(int dollars, int quarters, int dimes, int nickels, int pennies)
...//more code goes here
public static final double NICKEL_VALUE = 0.05;
public static final double DIME_VALUE = 0.1;
public static final double QUARTER_VALUE = 0.25;
}
Split CashRegister class into two classes - Payment and Coin. Payment class will contain enterPayment method, member variables for payment amount and constructors. Coin class will contain member variables for coin values and methods to get coin values.
The CashRegister class has multiple responsibilities - it is responsible for both payment entry and coin values. This violates the Single Responsibility Principle (SRP) and decreases cohesion. To increase cohesion, split CashRegister class into two classes - Payment and Coin. Payment class will contain enterPayment method, member variables for payment amount and constructors.
Coin class will contain member variables for coin values and methods to get coin values. In this way, each class will have a single responsibility and will be more cohesive. Additionally, accessors and mutators can be added to allow for controlled access to member variables. Constructors can also be added to initialize member variables. This approach will result in a more modular and maintainable codebase.
Learn more about CashRegister here:
https://brainly.com/question/24076338
#SPJ11
In a database, what is metadata? Compare this to cell phone metadata or document metadata (this has been in the news). How are they similar and how are they different?
In a database, metadata refers to the data that describes other data. It provides information about a particular set of data, such as its structure, organization, and context. Comparing this to cell phone metadata and document metadata, there are similarities and differences between them.
Cell phone metadata refers to the information that describes the details of phone calls, such as the phone numbers involved, the duration of the call, and the time and date of the call. Document metadata, on the other hand, refers to the information that describes the details of a digital document, such as its author, creation date, and keywords.
The similarities between database metadata, cell phone metadata, and document metadata include:
1. All three types of metadata provide descriptive information about the primary data.
2. They help in organizing, understanding, and managing the primary data.
3. All types of metadata can be used for searching, filtering, and sorting the primary data.
The differences between database metadata, cell phone metadata, and document metadata include:
1. Database metadata describes the structure, organization, and context of data in a database, while cell phone metadata describes the details of phone calls, and document metadata describes the details of digital documents.
2. The specific information contained in each type of metadata varies depending on the nature of the primary data.
In summary, metadata in a database, cell phone, and document all serve the purpose of providing additional information about the primary data they describe, but the specific details and nature of that information vary depending on the context.
To learn more about databases visit : https://brainly.com/question/518894
#SPJ11
Microsoft Access, Oracle, and SQL are examples of Relational Data Base. Relational DataBase: A relational database is a collection of data items with pre-defined relationships between them.
Microsoft Access, Oracle, and SQL are all examples of Relational Database Management Systems (RDBMS). RDBMS are software systems designed to manage and store data in a relational format, which means that the data is organized into tables with pre-defined relationships between them.
This allows for efficient storage, retrieval, and manipulation of large amounts of data. Both Microsoft Access and Oracle are popular RDBMS used in various industries for managing data, while SQL is a programming language used to interact with relational databases.
Microsoft Access, Oracle, and SQL are examples of Relational Database Management Systems (RDBMS). These systems manage relational databases, which are collections of data items with pre-defined relationships between them.
The relational model helps organize data efficiently and enables users to perform various operations such as querying, updating, and managing the data easily.
learn more about Relational Database Management Systems here: brainly.com/question/13261952
#SPJ11
You include the jQuery library in your website by coding a
Question 4 options:
head element
body element
script element
link element
You include the jQuery library in your website by coding a script element.
Write a short note on the jQuery library.jQuery is a fast, small, and feature-rich JavaScript library that simplifies client-side scripting of HTML. It provides an easy-to-use API that makes it easy to traverse and manipulate the HTML DOM tree, handle events, create animations, and make asynchronous HTTP requests. jQuery is widely used by web developers as it simplifies the process of creating dynamic web pages and user interfaces.
The library is designed to be compatible with all modern web browsers and has been extensively tested on all major browsers, including Internet Explorer, Firefox, Chrome, Safari, and Opera. It has a modular structure that allows developers to include only the features they need, reducing the overall file size and improving performance. jQuery is open-source software released under the MIT License, which means it can be freely used, modified, and distributed by anyone.
To learn more about jQuery, visit:
https://brainly.com/question/29314537
#SPJ1
a(n) ____________________ is a sequence of actions a user will perform when using the program.
Answer:
combination
Explanation:
why is a stack not good for round robin schedulers ? but a queue is. explain reasons for both.
A stack is not good for round robin schedulers because it follows the last-in, first-out (LIFO) principle. This means that the most recent process added to the stack will be executed first, which contradicts the round robin principle of giving equal time slices to each process.
On the other hand, a queue is good for round robin schedulers because it follows the first-in, first-out (FIFO) principle. This means that the first process added to the queue will be executed first, and each process will get an equal time slice before moving on to the next process. This aligns with the round robin principle and ensures fair scheduling for all processes.
In summary, a stack is not suitable for round robin schedulers because it doesn't prioritize equal time slices for each process, while a queue is a better choice because it follows the FIFO principle, which aligns with the round robin principle.
Learn more about stack: https://brainly.com/question/29578993
#SPJ11
a _____ is a collection of data that is defined in a directory and occupies space on a piece of media specifically allocated to that file.
Answer:
A File
[tex]hope \: it \: helps \: \\ if \: then \: pls \: brainliest < 3[/tex]
Which plans would you expect to be driven by assessments such as SLE, ARO, or ALE?1. Business continuity plan2. Contingency operations plan3. Information security incident response plan4. Risk management plan
Answer:
The answer is: Information Security Incident.
which command should you enter at the command prompt to list the tasks in the at queue for the current user?
The command to list the tasks in the at queue for the current user could be any of the following:
for Linux or macOS, you can use the "atq" commandfor Windows, you can use the `at` command with the "list" parameterWhat is a command prompt?The command prompt is a non-graphical interface that allows users to execute a series of commands by typing them into a terminal or console window. In Windows, you can access the command line by opening Command Prompt or Windows PowerShell from the Start menu.
The command to list the tasks in the at queue for the current user would depend on the operating system being used. Here are a few examples:
For Linux or macOS, you can use the `atq` command
For Windows, you can use the "at" command with the "list" parameter
Both of these commands will display a list of the tasks in the at queue for the current user.
learn more about command prompt: https://brainly.com/question/25808182
#SPJ4
O(N) is the order of growth execution time of the isFull operation when using the ArrayBoundedQueue class, assuming a queue size of N.TrueFalse
The given statement "O(N) is the order of growth execution time of the isFull operation when using the ArrayBoundedQueue class, assuming a queue size of N" is false becasue the isFull operation of the ArrayBoundedQueue class has a constant time complexity of O(1), which means its execution time does not depend on the size of the queue. Therefore, its order of growth execution time is O(1), not O(N).
The order of growth execution time of the isFull operation when using the ArrayBoundedQueue class, assuming a queue size of N, is O(1), not O(N). This is because the isFull operation only needs to compare the number of elements in the queue to the maximum capacity of the queue, which can be done in constant time.
Therefore, regardless of the size of the queue, the isFull operation will have the same execution time. The ArrayBoundedQueue class uses an array to store the elements in the queue, and the size of the array is fixed at the time of initialization. Therefore, the isFull operation is simply checking if the number of elements in the queue equals the size of the array.
You can learn more about ArrayBoundedQueue at
https://brainly.com/question/17119604
#SPJ11
Printing array elements separated by commas. Write a for loop to print all NUM_VALS elements of array hourly Temp. Separate elements with a comma and space. Ex: If hourly Temp = (90, 92, 94, 95), print: 90, 92, 94, 95 Your code's output should end with the last element, without a subsequent comma, space, or newline.
Code: for i in range(NUM_VALS): print(hourlyTemp[i], end='' if i == NUM_VALS-1 else ', ')
The for loop iterates through each element of the array, and the print statement outputs the current element. The 'end' parameter of the print statement is used to specify what should come after the printed text. If it is the last element of the array, 'end' is set to an empty string to prevent an extra comma and space from being printed. Otherwise, 'end' is set to a comma and space to separate each element.
Learn more about array here:
https://brainly.com/question/19570024
#SPJ11
Barrier Islands - Cape Hatteras, NC. Why is most of the construction on the lagoon side of the barrier Island (Problem 8 placemark)? a. more sunlight b. protected from storm waves and erosion C. land there is at a higher elevation d. there are more beach sands on that side
The reason why most of the construction on the barrier Island of Cape Hatteras, NC is on the lagoon side (Problem 8 placemark) is because it is b) protected from storm waves and erosion.
The lagoon side is shielded from the strong ocean currents and waves, which can cause significant damage to the structures built on the beach side. Therefore, construction on the lagoon side is more stable and secure.
The land there is not necessarily at a higher elevation or receiving more sunlight, and the availability of beach sands does not necessarily impact the location of construction on the barrier island. So the correct answer is b) protected from storm waves and erosion.
Learn more about barrier island: https://brainly.com/question/1647030
#SPJ11
a) What would mystery(3) be?
b) How many local variables are used in this function? (hint: how much stack space is used?)
c) Translate this function into an equivalent recursive python function.
d) This function has a specific name. What is that name?
To determine the value of mystery(3). I need the code for the mystery function. Please provide the function definition for further assistance.
Without knowing the specific function, I cannot determine the number of local variables or stack space used. Please provide the function definition. To translate the function into an equivalent recursive Python function, I would need the original function definition. Once you provide that, I can help you with the translation. To identify the specific name of the function, please provide the function definition or its purpose, and I'll be happy to help you identify its name.
To learn more about mystery click the link below:
brainly.com/question/14010230
#SPJ11
Given that two hosts A and Buse a selective-repeat protocol with a sliding-window of size 4 packets and a 3-bit sequence number. Suppose that host A has transmitted 6 packets to host B and that the third packet was lost in transit. Answer the following questions about the diagram. At event A, the following actions will take place Host A Host B pkt0 sent 01 2 34 56 pktl sent 0123456789 pkt0 revd, delivered, ACKO sent 0 1 2 3 4 56 pktl revd, delivered, ACKi sent pkt2 sent 0 1 2 3 4 5 6789(s) : 012 3 4 56789 Loss) pkt3 sent, window full 0 1 2 3 4 5 6789 Event A Event B EventC EventF Event D pkt2 TIMEOUT Event E Pkt3 receved,buffered, ACK3 sent O PK3 received, discarded, ACK2 sent O PK3 received, discarded, ACK3 sent receiver window will move to begin at3
In this scenario, the selective-repeat protocol is utilized to ensure accurate data transmission despite packet loss, and the 3-bit sequence number helps keep track of the order of the transmitted packets.
The two hosts A and B use a selective-repeat protocol with a sliding-window of size 4 packets and a 3-bit sequence number, and that host A has transmitted 6 packets to host B with the third packet being lost in transit, let's analyze the events provided in the diagram:
Step:1. Event A: Host A's window is full after sending packets 0, 1, 2, and 3. Host B receives packets 0 and 1, delivers them, and sends ACKs for them. Host B also receives packet 3, but it is buffered since packet 2 is still missing.
Step:2. Event B: Packet 2 is lost.
Step:3. Event C: Host B receives a duplicate packet 3 but discards it and sends an ACK for packet 3.
Step:4. Event D: Host B receives another duplicate packet 3, discards it, and sends an ACK for packet 3.
Step:5. Event E: Packet 2 experiences a timeout at Host A.
Step:6. Event F: After receiving the buffered packet 3 and missing packet 2, Host B's receiver window will move to begin at sequence number 3.
In this scenario, the selective-repeat protocol is utilized to ensure accurate data transmission despite packet loss, and the 3-bit sequence number helps keep track of the order of the transmitted packets.
Learn more about selective-repeat protocol here, https://brainly.com/question/29854395
#SPJ11
In cell F4, create a formula using the HLOOKUP function to determine the cost per participant for the workshop based on the Workshop ID in cell C4. Use range B16:E17 as the lookup table, and the Cost per participant listed in row 2 of the lookup table. Do not enter a value for the optional range_lookup argument.
To create a formula using the HLOOKUP function in cell F4, following the given instructions, use the following formula: =HLOOKUP(C4, B16:E17, 2, FALSE)
What is the explanation for the above response?C4 is the Workshop ID that we want to look up in the table.
B16:E17 is the lookup table that we want to search.
2 specifies that we want to return the value from the second row of the lookup table, which contains the cost per participant.
FALSE specifies that we want an exact match for the Workshop ID in cell C4.
The HLOOKUP function will search for the Workshop ID in cell C4 in the first row of the lookup table, and return the corresponding value from the second row, which is the cost per participant for that workshop. The result will be displayed in cell F4.
Learn more about HLOOKUP function at:
https://brainly.com/question/29095370
#SPJ1
1. what is the relationship between logical and physical models?
The relationship between logical and physical models is that they are two different views of the same system. A logical model is an abstract representation of a system that describes its functional requirements, business rules, and relationships between entities.
It is independent of any specific technology or implementation. A physical model, on the other hand, is a concrete representation of a system that describes its physical components, such as hardware, software, and databases. It is dependent on the technology used to implement the system. The logical model serves as a blueprint for the physical model, which is designed to meet the requirements of the logical model.
The physical model is derived from the logical model and serves as the basis for building and implementing the system. Therefore, the logical model and physical model are complementary and interconnected, and both are essential for designing and implementing a successful system.
Learn more about physical models: https://brainly.com/question/1511455
#SPJ11
state the types of Data range
There about 5 types of data range. See them below.
What are the various types of data range?Numeric range: This is a range of values that can be expressed as a numerical value.
Boolean range: This is a range of values that can be either true or false. Boolean data types are commonly used for logical expressions and conditional statements.
Character range: This is a range of values that can be represented as a character or string of characters. Character data types are commonly used for text-based data.
Date/time range: This is a range of values that can be expressed as a date or time value. Date/time data types are commonly used for tracking events or scheduling tasks.
Enumeration range: This is a range of values that can be expressed as a predefined set of values.
Learn more about data range at:
https://brainly.com/question/20607770
#SPJ1
a technician is selecting a server that will be used by a cloud provider to provide fault tolerance for large quantities of stored data. what is a major consideration that needs to be taken into account
The major consideration that needs to be taken into account is the server's capacity for redundancy and backup.
In order to provide fault tolerance for large quantities of stored data, the selected server must have the capability to maintain redundancy and backup. This means that the server should have built-in features that ensure data is replicated and stored in multiple locations, so that if one location fails, the data can still be retrieved from another location.
Additionally, the server should have backup solutions in place, such as regular backups and disaster recovery plans, to ensure that data can be restored in the event of a major failure or outage. Overall, the capacity for redundancy and backup is crucial for ensuring the reliability and availability of data in a cloud computing environment.
To know more about server visit:
https://brainly.com/question/7007432
#SPJ11
Which qualification is most important for a person who wants to serve there country?
The qualification that is most important for a person who wants to serve their country depends on the specific role they are interested in.
For example, someone interested in serving in the military may need to meet certain physical fitness requirements, have a high school diploma or equivalent, and pass various tests and screenings. On the other hand, someone interested in serving in government may need to have a college degree in a relevant field, such as political science or public administration. However, regardless of the specific role, a person who wants to serve their country should possess qualities such as dedication, loyalty, and a strong work ethic. Ultimately, the ability and willingness to serve and uphold the values of their country is the most important qualification for anyone looking to serve.
learn more about serve their country here:
https://brainly.com/question/30870749
#SPJ11
When we use 8-bit direct mode addressing in an instruction such as ADDWF, where does the 8-bit file-register address come from?
When using 8-bit direct mode addressing in an instruction such as ADDWF, the 8-bit file-register address comes from the operand field of the instruction itself. This means that the address is specified within the instruction code, allowing the processor to access the correct file register in memory and perform the desired operation.
ADDWF FILE_REGISTER, DESTINATION
Here's a step-by-step explanation:
1. ADDWF is the instruction mnemonic for "Add W and File Register."
2. FILE_REGISTER is the 8-bit file-register address, which is a part of the instruction. It indicates the specific register in the memory where the data is stored.
3. DESTINATION specifies where the result of the addition operation will be stored, either in the W register (WREG) or the file register itself.
In summary, when using 8-bit direct mode addressing in an instruction like ADDWF, the 8-bit file-register address comes directly from the instruction and specifies the location of the data to be used in the operation.
to know more about 8-bit file-register here:
brainly.com/question/29309118
#SPJ11
explain the difference between open source and proprietary database systems.
Open source database systems are those that are freely available for anyone to use, modify, and distribute, while proprietary database systems are owned by a particular company and their use, modification, and distribution are restricted to the terms and conditions set by the company.
One major difference between the two is that open source database systems have a larger community of developers and users who contribute to the development and improvement of the system. Proprietary database systems, on the other hand, are typically developed and maintained by a single company, and their features and capabilities are determined by the company's goals and resources. Open source database systems are often used in environments where customization and flexibility are important, while proprietary database systems are often used in more traditional business settings where data security and reliability are top priorities.
Overall, the choice between open source and proprietary database systems will depend on a variety of factors, including the specific needs of the organization, the resources available for development and maintenance, and the level of customization and control required.
To know more about database systems, please visit:
https://brainly.com/question/31113501
#SPJ11
hw15-2 determine the force in member dg of the truss in terms of the load l. all internal angles are 60.
The force in member DG of the truss in terms of the load L is (sqrt(3)/2)*L.
The truss is in static equilibrium, which means that the forces acting on it must balance out. By applying the method of joints, we can solve for the forces in each member. Since all internal angles of the truss are 60 degrees, we can use trigonometry to solve for the forces in each member.
To solve for the force in member DG, we can consider the joint where members DG, EG, and EF meet. We know that the force in member EF is equal to the load L, and we can use trigonometry to find the forces in members DG and EG. Once we have these forces, we can use the method of joints again to find the force in member DG in terms of the load L. The final expression for the force in member DG is (sqrt(3)/2)*L.
For more questions like Equilibrium click the link below: https://brainly.com/question/30807709 #SPJ11
Suppose that you have the following definitions:
struct timeType struct tourType
{ {
int hr; string cityName;
double min; int distance;
int sec; timeType travelTime;
}; };
Declare the variable destination of type tourType.
tourType destination;
Write C++ statements to store the following data in destination: cityName—Chicago, distance—550 miles, travelTime—9 hours and 30 minutes.
tourType.cityName = ‘Chicago’;
tourType.distance = 550;
tourType.travelTime.hr = 9;
tourType.travelTime.min = 30;
Write the definition of a function to output the data stored in a variable of type tourType.
Write the definition of a value-returning function that inputs data into a variable of type tourType.
Write the definition of a void function with a reference parameter of type tourType to input data in a variable of type tourType
To initialize (establish) variables. Assign a value to a variable named variableName, which is of one of the types available in Java, such as int or String. The symbol of equality is used for assigning values to a variable.
What is the variable about?The initial section of the code involves declaring the tourType variable, which is assigned the name "destination". The tourType struct comprises various elements such as the name of the city, the distance involved, and the duration of the journey.
The section of the code involves the assignment of cityName, distance, hr, and min values to the destination. The process requires utilizing the dot notation to access the suitable element of the target variable. Values are assigned to the travelTime's hr and min properties as well.
Learn more about variable from
https://brainly.com/question/24657796
#SPJ1
Consider two real-time processes with the following parameters:
Process P1 has the period p1 = 100 ms and execution time t1 = 15 ms.
Process P2 has the period p2 = 30 ms and execution time t2 = 20 ms
Both processes are ready to execute at time = 0, and the relative deadlines are equal to periods. The system has only one processor. Answer the following subquestions i.), ii.), iii.): and iv.)
iii.) Now assume we are using RMS and both processes are ready to execute at time = 0. Produce the Gantt chart on a separate piece of paper; and answer the following:
What processes are executed by the CPU from time 0 to 150? Give the exact time intervals. For example, if P1 executes from time = 0 to 10, P2 executes from time = 10 to 15, and the CPU is idle from 15 to 20, you can enter:
P1: 0 – 10: P2 10 – 15: idle: 15 – 20
iv.) Did all the process instances meet their deadlines during the time interval [0 - 150], when we use RMS? If not, what is the first process instance that missed its deadline, and what deadline has been missed?
iii.) The Gantt chart for RMS scheduling is as follows:
The ProgramTime 0 - 30: P1
Time 30 - 50: P2
Time 50 - 60: P1
Time 60 - 90: P1
Time 90 - 100: P2
Time 100 - 120: P1
Time 120 - 150: P1
The CPU executes process P1 for the first time interval from time 0 to 30. Then, it executes process P2 for the next time interval from time 30 to 50. After that, the CPU goes back to process P1 and executes it from time 50 to 60. Next, the CPU executes process P1 again from time 60 to 90. Then, the CPU executes process P2 from time 90 to 100.
Finally, the CPU executes process P1 for the remaining time intervals from time 100 to 150.
iv.) All the process instances meet their deadlines during the time interval [0-150] when we use RMS. The deadlines for both processes are equal to their respective periods. In this case, P1 has a period of 100 ms and executes for 15 ms, so it has a slack time of 85 ms before its next deadline.
Similarly, P2 has a period of 30 ms and executes for 20 ms, so it has a slack time of 10 ms before its next deadline. Therefore, both processes complete their execution within their respective deadlines.
Read more about programs here:
https://brainly.com/question/28959658
#SPJ1
Once the mass update process is initiated, no additional changes can be applied. (True or False)
Answer:
True
Explanation:
I believe that this is true because I have taken computer classes, coding, and other courses during the summer.
True. Once the mass update process is initiated, the system locks the records being updated and no additional changes can be applied until the process is complete.
It is important to review all changes carefully before initiating the mass update process to avoid any errors or unintended consequences. It is also recommended to have a backup plan in case any issues arise during the mass update process.
True. Once the mass update process is initiated, no additional changes can be applied. This means that after starting the mass update, any further modifications or updates cannot be performed until the current process is complete. This ensures that the system remains stable and data integrity is maintained during the update process.
Learn more about data integrity at: brainly.com/question/31076408
#SPJ11
write the definition of the function delete vector duplicates() that passes an stl vector of type int. the function deletes all duplicates. assumption: the vector has at least two elements.
The function delete_vector_duplicates() that passes an STL vector of type int is,the function uses the sort() function to sort the vector in ascending order, the unique() function to remove consecutive duplicates, and the erase() function to remove the remaining elements from the unique iterator to the end of the vector.
What is the implementation of the function delete_vector_duplicates() for an STL vector of type int in C++?
The definition of the function delete_vector_duplicates() that passes an STL vector of type int is as follows:
`void delete_vector_duplicates(std::vector& vec)`
This function takes a reference to an STL vector of integers (vec) and deletes all duplicate elements. The steps to implement this function are:
Learn more about function
brainly.com/question/29249394
#SPJ11