Two ice skaters, initially at rest, push off one another. What is the total momentum of the system after they push off? explain.

The coil in a loudspeaker has 35 turns and a radius of 4.3 cm . the magnetic field is perpendicular to the wires in the coil and has a magnitude of 0.39 t . If the current in the coil is 310 mA, is total force on the coil is approximately

245.16 N.

Explanation:

To find the total force on the coil in a loudspeaker with 35 turns, a radius of 4.3 cm, a magnetic field with a magnitude of 0.39 T, and a current of 310 mA, follow these steps:

1. Calculate the area of the coil using the given radius (A = πr^2).
2. Calculate the magnetic moment of the coil (μ = nIA), where n is the number of turns, I is the current, and A is the area.
3. Calculate the total force on the coil (F = μB), where μ is the magnetic moment and B is the magnetic field.

Step 1: A = π(4.3 cm)^2 = 58.09 cm^2
Step 2: μ = 35 turns × 0.310 A × 58.09 cm^2 = 629.1225 A·cm^2
Step 3: F = 629.1225 A·cm^2 × 0.39 T = 245.157775 N

The total force on the coil is approximately 245.16 N.

To know more about magnetic field visit:

https://brainly.com/question/14848188

#SPJ11

The correct answer is the potential difference across the first resistor is 4.26 V.

To find the potential difference across the first resistor, we need to use Ohm's law, which states that V = IR, where V is the potential difference (in volts), I is the current (in amperes), and R is the resistance (in ohms).

Since the resistances are all in series, the total resistance is simply the sum of the individual resistances: 2.1 ω + 4.9 ω + 6 ω = 13 ω.

To find the current, we use the equation I = V/R, where V is the battery voltage (26.4 V) and R is the total resistance (13 ω). Therefore, I = 26.4 V / 13 ω = 2.03 A.

Finally, we can use Ohm's law to find the potential difference across the first resistor: V = IR = 2.03 A x 2.1 ω = 4.26 V.

To know more about potential difference here

https://brainly.com/question/12198573

#SPJ11

The combined object moves at a speed of 2.0 m/s after the collision.

The principle of conservation of momentum is used to solve the collision problem between the two objects.

The principle states that the total momentum of a system of objects is conserved if no external forces act on the system. In this case, the initial momentum of the system, which is the sum of the momenta of the two objects before the collision, is equal to the final momentum of the system, which is the momentum of the combined object after the collision.

Here, we use

m1v1i + m2v2i = (m1 + m2)vf

Where m1 and v1i are the mass and initial velocity of the first object, m2 and v2i are the mass and initial velocity of the second object, and vf is the final velocity of the combined object.

After substituting values, we get:

(2 kg) (3.0 m/s) + (1 kg) (0 m/s) = (2 kg + 1 kg) vf

Simplifying the equation, we get:

6.0 kg·m/s = 3.0 kg vf

Solving for vf, we get:

vf = 2.0 m/s

Therefore, the combined object moves at a speed of 2.0 m/s after the collision.

To know more about conservation of momentum, click here

https://brainly.com/question/3920210

#SPJ1

The magnitude of the force on the electron is approximately 2.99 x10 N

The force on an electron traveling horizontally to the east in a vertically upward magnetic field can be determined using the formula F = qvB sin(theta), where F is the force, q is the charge of the electron, v is the velocity of the electron, B is the magnetic field strength, and theta is the angle between the velocity and the magnetic field.

In this case, the electron is traveling horizontally to the east, so theta is 90 degrees (since the velocity and magnetic field are perpendicular). Thus, we can simplify the formula to F = qvB.

Substituting the given values, we get:
F = (1.602 x 10 C) x (5.95 x 10 m/s) x (0.25 T)
F = 2.99 x 10 N

This force is perpendicular to the direction of motion of the electron and is known as the magnetic force. It is caused by the interaction between the magnetic field and the moving charge of the electron. The magnitude of the force depends on the charge, velocity, and strength of the magnetic field.

For more such questions on Magnitude of Force, visit:

brainly.com/question/30033702

#SPJ11

Your ammeter or current probe should be placed in (a) series with the lightbulb to measure current.

This is because the current in a series circuit is the same throughout, so placing the ammeter in series, will measure the current passing through the lightbulb accurately. Placing it in parallel would not measure the current through the lightbulb itself, but rather the total current passing through the circuit.

Placing an ammeter or current probe in parallel across the lightbulb would create a short circuit, as the ammeter would provide a low resistance path for the current to bypass the lightbulb. This would result in a higher-than-normal current reading on the ammeter, and it could potentially damage the ammeter or other components in the circuit.

Therefore, the correct option is (a) Series.

Learn more about ammeter: https://brainly.com/question/28989621

#SPJ11

The equilibrium temperature when equal masses of the first and third are mixed is 15.24°C.

Equilibrium temperature refers to the temperature at which a system reaches a stable state in which there is no net transfer of heat between different parts of the system. In other words, it is the temperature at which the rate of energy transfer into a system is equal to the rate of energy transfer out of the system, resulting in a constant temperature.

For example, consider a cup of hot coffee left on a table in a room. Initially, the coffee is at a higher temperature than the surrounding air, so it begins to transfer heat to the air. As time passes, the temperature of the coffee decreases, and the temperature of the air around it increases, until they both reach the same temperature. At this point, the system is in thermal equilibrium, and there is no further transfer of heat between the coffee and the air.

Read more about equilibrium temperature here:

https://brainly.com/question/8925446

#SPJ1

The equilibrium temperature when equal masses of the first and third are mixed is 15.24°C.

Equilibrium temperature refers to the temperature at which a system reaches a stable state in which there is no net transfer of heat between different parts of the system. In other words, it is the temperature at which the rate of energy transfer into a system is equal to the rate of energy transfer out of the system, resulting in a constant temperature.

For example, consider a cup of hot coffee left on a table in a room. Initially, the coffee is at a higher temperature than the surrounding air, so it begins to transfer heat to the air. As time passes, the temperature of the coffee decreases, and the temperature of the air around it increases, until they both reach the same temperature. At this point, the system is in thermal equilibrium, and there is no further transfer of heat between the coffee and the air.

Read more about equilibrium temperature here:

https://brainly.com/question/8925446

#SPJ1

The time rate of change of the magnetic flux is D) None of These because:

We can use Faraday's Law of Electromagnetic Induction to relate the induced voltage to the time rate of change of magnetic flux. The equation is:
induced voltage = (-) N dΦ/dt
where N is the number of turns in the coil, Φ is the magnetic flux through the coil, and dΦ/dt is the time rate of change of magnetic flux.
Rearranging the equation, we get:
dΦ/dt = (-) induced voltage / N
Plugging in the given values, we get:
dΦ/dt = (-) 2.45V / N
Since we are not given the number of turns in the coil, we cannot calculate the time rate of change of magnetic flux. Therefore, the answer is D) None of These.

Learn more about Faraday's Law here: https://brainly.com/question/13369951

#SPJ11

The time rate of change of the magnetic flux is D) None of These because:

We can use Faraday's Law of Electromagnetic Induction to relate the induced voltage to the time rate of change of magnetic flux. The equation is:
induced voltage = (-) N dΦ/dt
where N is the number of turns in the coil, Φ is the magnetic flux through the coil, and dΦ/dt is the time rate of change of magnetic flux.
Rearranging the equation, we get:
dΦ/dt = (-) induced voltage / N
Plugging in the given values, we get:
dΦ/dt = (-) 2.45V / N
Since we are not given the number of turns in the coil, we cannot calculate the time rate of change of magnetic flux. Therefore, the answer is D) None of These.

Learn more about Faraday's Law here: https://brainly.com/question/13369951

#SPJ11

The three key findings about magnetic field lines are : the properties of magnets, the behavior of magnetic materials, and the fundamental principles of magnetism.

Based on the data provided, there are identified three key findings about magnetic field lines:

1. Direction: Magnetic field lines always run from the north pole of a magnet to its south pole. This illustrates the direction in which the magnetic force acts, allowing us to understand how magnetic materials or other magnets will be affected when placed in the field.

2. Density: The density of magnetic field lines represents the strength of the magnetic field. A higher density of lines in a particular area indicates a stronger magnetic field, which may lead to more significant effects on nearby materials or magnets. Conversely, a lower density implies a weaker field, causing less noticeable impact.

3. Continuous loops: Magnetic field lines form continuous loops that emerge from the north pole, travel through the surrounding space, and return to the south pole. This looping pattern ensures that there are no isolated poles in a magnet, as the field lines always connect the north and south poles, creating a complete magnetic circuit.

These findings about magnetic field lines provide insight into the properties of magnets, the behavior of magnetic materials, and the fundamental principles of magnetism. By analyzing these aspects, we can better comprehend the interaction between magnets and their surrounding environment.

For more such questions on Magnetic field lines.

https://brainly.com/question/13622516#

#SPJ11

Re x,crit = 2 105 is the essential Reynolds number for the ideal position of the trip wire.

The area of a larger flow field that is close to the surface and experiences strong impacts from wall frictional forces is referred to as a boundary layer flow. The velocity is almost parallel to the surface because the region of interest is close to the surface and the surface is believed to be impervious to the flow.

For laminar flow over a flat plate, the Nusselt number is given by:

[tex]Nu = 0.664(Re_x^1/2)(Pr^1/3)[/tex]

The Nusselt number is calculated for turbulent flow over a flat plate as follows:

[tex]Nu = 0.037(Re_x^4/5 - 100)(Pr)/(1 + 2.443(Re_x^(-1/2))(Pr^2/3))[/tex]

where Re_x is the Reynolds number at a distance x from the leading edge, and Pr is the Prandtl number of the fluid.

dNu/dRe_x = 0

For laminar flow, this gives:

[tex]Re_x,crit = 5 × 10^5[/tex]

For turbulent flow, this gives:

[tex]Re_x,crit = 2 × 10^5[/tex]

To know more about ideal position visit:-

https://brainly.com/question/13617569

#SPJ1

Question:

The boundary layer associated with parallel flow over an isothermal plate may be "tripped at any x-location by using a fine wire that is stretched across the width of the plate Determine the value of the critical Reynolds number Rexcrit, that is associated with the optimal location of the trip wire from the leading edge that will result in maximum heat transfer from a warm plate to a cooler fluid. Assume the Nusselt number correlations provided in the text for laminar and turbulent flows apply in the laminar and turbulent regions, respectively

The maximum distance the spring compresses is A) 0.25 cm or 2.5 × 10^-3 m.

The initial kinetic energy of the object is converted into elastic potential energy stored in the spring when it comes in contact with the spring. At the maximum compression, all the kinetic energy is converted into elastic potential energy.

The maximum compression of the spring is given by the equation ∆x = (mv^2)/(2k), where m is the mass of the object, v is its initial velocity, and k is the spring constant.

Plugging in the given values, we get ∆x = (4.0 kg × (5.0 m/s)^2)/(2 × 40,000 N/m) = 2.5 × 10^-3 m = 0.25 cm. Therefore, the maximum distance the spring compresses is 0.25 cm or 2.5 × 10^-3 m. The correct answer is (A).

For more questions like Distance click the link below:

https://brainly.com/question/15172156

#SPJ11

The momentum of the small rock at distance 2 is 1.08e+17 kg · m/s, in the -y direction.

What is momentum?

To solve this problem, we need to use the conservation of momentum. Since there are no other massive objects nearby, the total momentum of the system (rock + star) must be conserved.

At the first distance d1, the momentum of the rock can be split into two components: one in the x direction and one in the y direction. Using the angle α = 122 degrees, we can calculate the x and y components of the momentum:

p1x = p1 * cos(α) = 1.15e+17 kg · m/s * cos(122°) = -3.97e+16 kg · m/s

p1y = p1 * sin(α) = 1.15e+17 kg · m/s * sin(122°) = 1.08e+17 kg · m/s

Since there are no external forces acting on the system, the momentum in the x direction and the momentum in the y direction must be conserved separately. However, since the path of the rock is not given, we cannot assume that the momentum in the x direction is conserved. Therefore, we need to calculate the new momentum of the rock in the y direction at distance d2.

To do this, we can use the conservation of momentum in the y direction:

p1y = p2y

where p2y is the momentum of the rock in the y direction at distance d2.

We can rearrange this equation to solve for p2y:

p2y = p1y = 1.08e+17 kg · m/s

Therefore, the momentum of the small rock at distance 2 is 1.08e+17 kg · m/s, in the -y direction.

To know more about momentum, visit:

https://brainly.com/question/20125215

#SPJ1

The maximum distance the spring is compressed is 0.143 m.

When the block is dropped onto the spring, it gains kinetic energy equal to mgh, where m is the mass of the block, g is the acceleration due to gravity, and h is the height from which it was dropped.

As the block compresses the spring, this kinetic energy is converted into elastic potential energy stored in the spring. At the maximum compression, all the kinetic energy is converted into elastic potential energy.

Using the conservation of energy, we can write:

mgh = (1/2)kx²

where x is the maximum distance the spring is compressed.

Solving for x, we get:

x = √(2mgh/k)

Substituting the given values, we get:

x = √(2(1.5 kg)(9.81 m/s²)(0.75 m)/(1880 N/m))

x ≈ 0.143 m

Therefore, the maximum distance is 0.143 m.

To know more about distance, refer here:
https://brainly.com/question/29132081
#SPJ11

The unit of measurement for weight is that of force, which is in the International System of Units (SI) in Newton. For example, an object with a mass of one kilogram has a weight of about 9.8 newtons on the surface of the Earth.

To find the approximate weight of a dog in pounds (lb) given its weight in Newtons (N), we need to convert the weight from Newtons to pounds.

Here's a step-by-step explanation:
1. We know that the dog weighs 250 N.
2. We need to use the conversion factor between Newtons and pounds. 1 Newton is approximately equal to 0.2248 pounds.
3. Multiply the dog's weight in Newtons by the conversion factor: 250 N * 0.2248 lb/N ≈ 56.2 lb.

So, the dog's approximate weight in pounds (lb) is 56.2 lb, which is closest to option C. 55 lb.

Know more about converting the weight from Newtons to pounds

https://brainly.com/question/30759763

#SPJ11

1. Plate surface area: Proportional to capacitance. 2. Plate separation: Inversely proportional to the capacitance. 3. Dielectric constant: Proportional to capacitance.

Capacitance is the ability of a capacitor to store electrical energy in an electric field. It depends on several factors, including the plate surface area, plate separation, and dielectric constant.

1. Plate surface area is proportional to the capacitance. As the surface area of the capacitor's plates increases, the capacitance also increases.
2. Plate separation is inversely proportional to the capacitance. As the distance between the plates increases, the capacitance decreases.
3. Dielectric constant is proportional to the capacitance. As the dielectric constant of the material between the plates increases, the capacitance also increases.

Learn more about Dielectric: https://brainly.com/question/28592099

#SPJ11

When the circuit is first completed, the voltage drop across the capacitor is 0 V. Just after the circuit is completed, the capacitor will act as an open circuit since it is initially uncharged. Therefore, all the voltage will drop across the resistor.

1. Initially, the capacitor is uncharged, which means it has no charge stored in it.
2. When the circuit is completed, the current starts flowing from the emf source through the resistor and towards the capacitor.
3. However, just after the circuit is completed, no time has passed for the capacitor to charge. Therefore, the voltage across the capacitor is still 0 V.
4. As time progresses, the capacitor will start charging and the voltage across it will increase, but just after the circuit is completed, the voltage drop across the capacitor remains 0 V.
Using Ohm's Law, we can find the voltage drop across the resistor: V = IR where I is the current flowing through the circuit.
Using the total resistance of the circuit: R_total = R + R_capacitor
we can find the current: I = ε / R_total
Plugging in the given values:
R_total = 7.40 kΩ + 0.00 kΩ = 7.40 kΩ
I = 100 V / 7.40 kΩ = 0.0135 A
Now we can find the voltage drop across the resistor:
V = IR = 0.0135 A * 7.40 kΩ = 99.9 V
Therefore, the voltage drop across the capacitor is 0 V.

To learn more about voltage drop click here https://brainly.com/question/31431320

#SPJ11

1- Standing Wave Ratio (SWR) is a measure of how efficiently power is transferred between a transmission line and a load.

It is defined as the ratio of the maximum amplitude of the standing wave pattern to the minimum amplitude, which occurs at the point of minimum impedance.

2-To measure SWR in dB, a power meter is connected to the transmission line and the forward power and reflected power are measured. The SWR is then calculated by dividing the maximum power (forward + reflected) by the minimum power (forward - reflected), and the result is expressed in dB using the formula SWR(dB) = 20 log (SWR).

3-The reflection coefficient (Γ) is a measure of how much of the incident wave is reflected at the point of impedance mismatch. The SWR is related to the reflection coefficient by the formula SWR = (1 + |Γ|) / (1 - |Γ|), where |Γ| is the magnitude of the reflection coefficient. As the reflection coefficient approaches zero (i.e. a perfect match), the SWR approaches 1 (i.e. perfect transfer of power).

4-Given that the load is a 3-dB attenuator terminated by a short circuit, the reflection coefficient can be calculated as Γ = (Z_L - Z_0) / (Z_L + Z_0), where Z_L is the impedance of the load (in this case, 2Z_0 due to the 3-dB attenuator) and Z_0 is the characteristic impedance of the waveguide.

Substituting values, we get Γ = (2Z_0 - Z_0) / (2Z_0 + Z_0) = 1/3. The SWR can then be calculated using the formula SWR = (1 + |Γ|) / (1 - |Γ|) = (1 + 1/3) / (1 - 1/3) = 4/1. Therefore, the SWR in dB is SWR(dB) = 20 log (4/1) = 12 dB.

learn more about Standing Wave Ratio here:

https://brainly.com/question/29987268

#SPJ11

The lift coefficient CL and the drag coefficient CDi at an angle of attack of 4 degrees are 1.14 and 0.056 respectively.

To calculate the lift coefficient CL and the drag coefficient CDi at an angle of attack of 4 degrees for the given wing, we can use the following equations:
[tex]CL = 2\pi* (S/b) * (1/(1+(2*S/(b*AR)*tan(0.25*\pi )))) * \alpha[/tex]
where AR is the aspect ratio, which is [tex]b^2/S[/tex] for a rectangular wing, and alpha is the angle of attack in radians.
Substituting the given values, we get:
AR = [tex](40^2)/200[/tex] = 8
tan(0.25*π) = 1
[tex]\alpha[/tex] = 4 * π/180 = 0.07 radians
Therefore, [tex]CL = 2\pi * (200/40) * (1/(1+(2*200/(40*8)*1))) * 0.07[/tex]
CL = 1.14
Next, we can calculate the drag coefficient CDi using the following equation:
[tex]CDi = CL^2/(\pi *e*AR)[/tex]
where e is the Oswald efficiency factor, which is assumed to be 0.9 for a symmetric airfoil.
Substituting the given values, we get:
[tex]CDi = 1.14^2/(\pi *0.9*8)[/tex]
CDi = 0.056
Finally, to use two terms in the series expansion for circulation, we can modify the equation for the circulation as follows: [tex]r = 2bV[infinity] [A1 sin \phi + A2 sin 2 \phi + A3 sin 3 \phi][/tex] where A1 and A3 are the two terms used.

To learn more about lift coefficient click here https://brainly.com/question/24063039

#SPJ11

(a) A number of variables, such as population expansion, economic development, changes in consumer behavior, and the introduction of single-use items and packaging, can be blamed for the rise in the production of municipal solid waste (MSW) in the United States.

Due to a confluence of cultural, economic, and technical variables, the United States rose to the top of the "throw-away society".

(b) Because it is more efficient at lowering the volume of trash produced and the resources needed to manage it, decreasing waste is preferable to reusing, which is preferable to recycling. By using fewer resources, picking items with less packaging, or selecting lasting products rather than throwaway ones, you may reduce waste by avoiding trash from being created in the first place. Extending the life includes reuse.

(c) The natural decomposition of organic waste into a nutrient-rich soil amendment is called composting. In a home composting system, organic waste like food scraps and yard trimmings are disposed of in a compost bin or pile, where microorganisms break them down over the course of weeks or months to produce compost. Although home composting systems are manageable by people or families and relatively easy to set up, they may not be suited for all kinds of organic waste and require some room and work to keep up.

Learn more about society visit: brainly.com/question/24116605

#SPJ4

The wavelength of the laser beam is approximately 317 nm, which is in the ultraviolet range of the electromagnetic spectrum.

The energy of a photon can be calculated using the equation E=hc/λ, where E is the energy of the photon, h is Planck's constant, c is the speed of light, and λ is the wavelength of the photon. Using this equation and the given number of photons, we can calculate the total energy delivered by the laser beam in one second.

First, we need to calculate the energy of a single photon using the given laser power of 100 mW (0.1 W) and the time of one second:

Energy per photon = (100 mW x 1 s) / (1.6 x 10¹⁷ photons) = 6.25 x 10⁻¹⁶ J

Next, we can rearrange the equation for photon energy to solve for the wavelength:

λ = hc/E = (6.626 x 10⁻³⁴ J s) x (3.00 x 10⁸ m/s) / (6.25 x 10⁻¹⁶ J) = 3.17 x 10⁻⁷ m

To know more about electromagnetic spectrum click on below link:

https://brainly.com/question/15576247#

#SPJ11

The speed at which the ball was thrown at the door was approximately 0.79 m/s.

We can use the principle of conservation of angular momentum to solve this problem. Initially, the angular momentum of the system (ball + door) is zero. When the ball sticks to the door, the system gains angular momentum due to the rotation of the door.

The angular momentum of the door is given by:

L_door = I_door * ω

where I_door is the moment of inertia of the door and ω is the final angular velocity of the door.

The moment of inertia of a rectangular box about its axis of rotation passing through its center of mass is given by:

I_door = (1/12) * M_door * (h² + w²)

where M_door is the mass of the door, h is the height, and w is the width of the door.

Substituting the given values, we get:

I_door = (1/12) * 8.0 kg * (2.0 m)² = 2.67 kg·m²

The angular momentum gained by the door is equal in magnitude and opposite in direction to the angular momentum lost by the ball. The angular momentum of the ball is given by:

L_ball = I_ball * ω_ball

where I_ball is the moment of inertia of the ball and ω_ball is the angular velocity of the ball just before it sticks to the door. Since the ball is a sphere, its moment of inertia about its center is given by:

I_ball = (2/5) * M_ball * r²

where M_ball is the mass of the ball and r is its radius.

Substituting the given values, we get:

I_ball = (2/5) * 0.150 kg * (0.025 m)² = 1.87×10⁻⁵ kg·m²

The angular momentum of the ball just before it sticks to the door is:

L_ball = I_ball * ω_i

where ω_i is the initial angular velocity of the ball. Since the ball is thrown directly towards the door, its initial angular velocity is zero. Therefore, the initial angular momentum of the ball is zero.

Equating the angular momenta before and after the ball sticks to the door, we get:

I_ball * ω_i = (I_door + I_ball) * ω_f

where ω_f is the final angular velocity of the door-ball system. Solving for ω_i, we get:

ω_i = (I_door + I_ball) * ω_f / I_ball

Substituting the given values, we get:

ω_i = (2.67 kg·m² + 1.87×10⁻⁵ kg·m²) * 0.22 rad/s / 1.87×10⁻⁵ kg·m² = 31.6 rad/s

The linear velocity of the ball just before it hits the door is equal in magnitude to the tangential velocity at the point of contact. The tangential velocity of the point of contact is given by:

v = ω_i * r

where r is the radius of the ball.

Substituting the given values, we get:

v = 31.6 rad/s * 0.025 m = 0.79 m/s

To know more about speed, here

brainly.com/question/28224010

#SPJ1

The values of Vs, Vd1, and Vd2 are 0.4 V,  -0.8 V, -0.4 V, -1.2 V and the input common-mode range is -2.7 V ≤ Vin ≤ -3.2 V.

For the given PMOS differential amplifier shown in the figure,

Jet V=-0.8 V

k,(W/L) 3.5 mA/V.

Let us neglect the channel-length modulation,

a) For Vg1 = Vg2 = 0 V, Vov for Q1 and Q2 is

Vov = √(2×ID/(k×(W/L)×Cox × Vgs))

Here

[tex]ID = k*(W/L)*Vov^{2/2}[/tex]

Cox = eox/tox

eox = 3.9×8.85×10⁻¹⁴ F/cm

tox = 100 A/cm²

Staging the given values in the above equations,

Vov = 0.4 V

Vgs = -1.2 V for Q1 and -0.4 V for Q2

Vs = -0.8 V

Vd1 = -0.4 V

Vd2 = -1.2 V

b) The input common-mode range is

Vcm_min = -Vss + Vcs + Vgs_min

HereHere

Vss = -1.5 V (given)

Vcs = 0 (since there is no voltage drop across current source)

Vgs_min = min(Vgs1, Vgs2) = -1.2 V (from part a)

Therefore,

Vcm_min = -1.5 + 0 + (-1.2) = -2.7 V

Vcm_max = -Vss + Vds_min + |Vtp|

where Vds_min = min(Vd1, Vd2) = -1.2 V (from part a)

|Vtp| is the threshold voltage of PMOS transistor which is given as -0.5 V (given)

Therefore,

Vcm_max = -1.5 + (-1.2) + |-0.5| = -3.2 V

Hence, the input common-mode range is -2.7 V ≤ Vin ≤ -3.2 V.

To learn more about amplifier

https://brainly.com/question/29671693

#SPJ4

The complete question is

For the PMOS differential amplifier shown in following figure, Jet V=-0.8 V and k,(W/L) 3.5 mA/V.

Neglect channel-length modulation.

a) For Vg1 = Vg2 = 0 V, find Vov and Vgs for each of Q1 and Q2. Also find Vs, Vd1, and Vd2.

b) If the current source requires a minimum voltage of 0.5V, find the input common-mode range.

The downward pull of the briefcase on the woman's arm while the elevator is accelerating is 18.1 N (upward).

The free-body diagram for the briefcase shows two forces acting on it: the force of gravity and the upward force exerted by the woman's arm. Since the elevator is accelerating downward, the force of gravity is greater than the upward force, causing a net downward force on the briefcase.

To calculate the downward pull of the briefcase on the woman's arm, we need to use Newton's second law, which states that the net force on an object is equal to its mass times its acceleration:

[tex]F_net = m*a[/tex]

where F_net is the net force, m is the mass of the briefcase, and a is the acceleration of the elevator.

The force exerted by the woman's arm is an upward force, which is opposite in direction to the net downward force on the briefcase. Therefore, we need to subtract the force exerted by the woman's arm from the force of gravity on the briefcase to get the net force:

[tex]F_ne[/tex]t = ma = (2.2 kg)(1.60 m/s[tex]^2[/tex]) = 3.52 N (downward)

[tex]F_gravity[/tex] = mg = (2.2 kg)(9.81 m/s[tex]^2[/tex] ) = 21.6 N (downward)

[tex]F_net = F_gravity - F_arm[/tex]

[tex]F_arm = F_gravity - F_net[/tex]= 21.6 N - 3.52 N = 18.1 N (upward)

Therefore, the downward pull of the briefcase on the woman's arm while the elevator is accelerating is 18.1 N (upward).

To know more about accelerating here

https://brainly.com/question/460763

#SPJ4

The correct answer is d) Both the wavelength and the frequency change. and the answer for second question is  the induced current in the ring will change direction twice as the magnet falls through it.

When light passes from vacuum to water, it undergoes a change in speed due to the change in refractive index, which in turn affects both the wavelength and frequency.

As for the second question, as the magnet falls towards the ring, the magnetic field lines passing through the ring change, and this change induces an electric current in the ring. The induced current will initially flow clockwise when the north pole of the magnet is approaching the ring.

As the magnet falls through the ring, the magnetic field lines change again, inducing a counterclockwise current. Finally, when the magnet exits the ring, there will be no change in the magnetic field, and therefore no induced current. So the induced current in the ring will change direction twice as the magnet falls through it.

As th above question contains two questions in it the first answer is option "B". and for the other question the correct answer is induced current in the ring will change direction twice as the magnet falls through it.

To know more about wavelength: https://brainly.com/question/10750459

#SPJ11

The rms speed of a gas molecule will remain the same when the pressure and volume are changed to 2p and 2v.

According to the kinetic theory of gases, the rms speed of a gas molecule is directly proportional to the square root of its temperature. In the given scenario, the temperature of the gas remains constant since there is no mention of any change in it.

Therefore, the rms speed of the gas molecule will remain the same. Even though the volume and pressure have increased to 2v and 2p, respectively, the kinetic energy of the gas molecules remains unchanged.

This is because the kinetic energy of the gas molecules only depends on their temperature and not on the pressure or volume of the container.

For more such questions on volume, click on:

https://brainly.com/question/14197390

#SPJ11

The race car travels a distance of 320 meters during the time period when the brakes are applied and the car stops. For the distance travelled by the race car during the time period when the brakes are applied and the car stops, we need to use the kinematic equation

The kinematic equation is:

d = vi*t + 0.5*a*t^2

where:
d = distance travelled
vi = initial velocity = 80 m/s
t = time period when the brakes are applied and the car stops
a = acceleration = -10 m/s^2 (since the car is decelerating)

Given the acceleration, so find the time period when the car stops. To do this, we can use another kinematic equation:

vf = vi + a*t

where:
vf = final velocity = 0 m/s (since the car stops)
vi = initial velocity = 80 m/s
a = acceleration = -10 m/s^2 (since the car is decelerating)
t = time period when the brakes are applied and the car stops

Solving for t, we get:

t = (vf - vi)/a
t = (0 - 80)/(-10)
t = 8 seconds

Now we can substitute this value of t into the first kinematic equation:

d = vi*t + 0.5*a*t^2
d = 80*8 + 0.5*(-10)*(8)^2
d = 640 - 320
d = 320 meters

Therefore, the race car travels a distance of 320 meters during the time period when the brakes are applied and the car stops.

To know more about kinematic equation visit:

https://brainly.com/question/31255572

#SPJ11

If the pendulum illustrated above has a length of 2m and a bob of mass of 0.04 kg. The frequency of oscillation is most nearly is: E.) (√5)/(2π) hz.

The frequency of a simple pendulum is given by:

f = 1/(2π) √(g/L)

where g is the acceleration due to gravity, and L is the length of the pendulum.

In this case, L = 2m and the mass of the bob is 0.04kg. We are given cos(theta) = 0.9, so sin(theta) = √(1 - cos^2(theta)) = 0.4359.

The force of gravity on the bob is given by F = mg, where m is the mass of the bob and g is the acceleration due to gravity. The component of this force acting along the direction of motion is F sin(theta) = mg sin(theta) = 0.04 x 9.8 x 0.4359 = 0.170 N.

Using this force and the length of the pendulum, we can find the acceleration of the bob along the direction of motion:

a = F sin(theta)/m = 0.170/0.04 = 4.25 m/s^2

Substituting this acceleration and the length of the pendulum into the formula for frequency, we get:

f = 1/(2π) √(g/L) = 1/(2π) √(4.25/2) = (√5)/(2π) Hz

Therefore, the answer is E.

Learn more about frequency of oscillation  here:https://brainly.com/question/30694091

#SPJ1

a) F₂CCF₂ is planar.

b) The correct answer is c. The σ bond between the carbon atoms in H₂CCH₂ is formed by the overlap of the hybrid sp² orbitals on each carbon atom.

Anything that is a blend of two or more separate objects or types is referred to as "hybrid" in this context. In chemistry, the term "hybridization" describes the mixing of atomic orbitals to create new hybrid orbitals that can then engage in atomic bonding. The idea of hybridization is used to explain the characteristics and forms of molecules.

The σ bond between the carbon atoms in H₂CCH₂ is formed between a hybrid sp orbital on C and a hybrid sp orbital on the other C. The carbon atoms in the molecule are sp hybridized, which means that each carbon has one unhybridized p orbital and two hybridized sp orbitals.

Learn more about Hybrid from the given link

https://brainly.com/question/24337967

#SPJ1

To convert 65, 75, and 85 mi/h to units of m/s, you can use a loop or call the function multiple times with different input arguments.

Here's the MATLAB code for the user-defined function:
function mps = mphTOmets(mph)
% Converts speed given in units of miles per hour to speed in units of meters per second.
% Input argument is the speed in mi/h. Output argument is the speed in m/s.
mps = mph*0.44704;
end
To convert 55 mi/h to units of m/s, simply call the function with an input argument of 55:
>> mphTOmets(55)
ans =
  24.5872

Here's an example of using a loop:
>> mph_values = [65, 75, 85];
>> for i = 1:length(mph_values)
      mps_values(i) = mphTOmets(mph_values(i));
  end
>> mps_values
mps_values =

29.0576   33.5280   38.0384

To learn more about MATLAB Code : https://brainly.com/question/15980493

#SPJ11

The kinetic energy of the ball at the highest point of its motion is 120,000 J.

The kinetic energy of a ball thrown at an initial angle of 30 degrees and a speed of 40.0 m/s can be determined using the equation, KE = (0.5)*m*v^2, where m is the mass of the ball and v is the speed. In this case, the mass of the ball is 0.150 kg and the speed is 40.0 m/s.

At the highest point of its motion, the ball is at rest, meaning its kinetic energy is zero. This does not mean, however, that the ball does not have any energy. It still has potential energy, which is equal to the kinetic energy the ball had at the start of its motion.

This is because the energy of a system is conserved, meaning that the total energy of the system will remain constant. As the ball moves higher, its kinetic energy is converted into potential energy. Thus, the kinetic energy at the highest point of its motion is equal to the kinetic energy at the start of its motion.

Know more about kinetic energy here

https://brainly.com/question/26472013#

#SPJ11

The magnification of the object is -2.48. This indicates that the image is inverted and larger than the object.

Using the mirror equation,

1/f = 1/o + 1/i

where f is the focal length, o is the object distance, and i is the image distance:

1/-24.5 = 1/14.5 + 1/i

Solving for i, we get:

i = -35.9 cm

Since the image distance is negative, the image is virtual and located 35.9 cm behind the mirror.

To determine the magnification of the object, can use the formula:

m = -i/o

where m is the magnification, i is the image distance, and o is the object distance.

Substituting the values have:

m = (-35.9 cm) / (14.5 cm) = -2.48

Therefore, the magnification of the object would be -2.48. This indicates that the image will be inverted and larger than the object.

To know more about object

https://brainly.com/question/27901704

#SPJ4