Answer:
A is correct!
Explanation:
e2020
Answer:
a
Explanation:
right on edge :)
What is the period of a wave that has a frequency of 30 Hz?
A. 0.3s
B. 0.03 s
C. 30 s
D. 35
Answer:
0.03s
Explanation:
Period of wave and its frequency are closely related. Period is the inverse of frequency.
The period of a wave is the time taken for a number of waves to pass through a particular point.
The frequency of a wave is the number of waves that passes through a point at a particular time.
So;
f = [tex]\frac{1}{T}[/tex]
f is the frequency
T is the period
Period of the wave = [tex]\frac{1}{30}[/tex] = 0.03s
Answer:
a
Explanation:
Phich instrument can be used to give a direct measurement of the mass of a rock on moon
Answer:
you can use a balance
Explanation:
when you tend to measure something you are using your brain so why dont you use your brain dimwitt
Temperatures of gases inside the combustion chamber of a four‑stroke automobile engine can reach up to 1000°C. To remove this enormous amount of heat, the engine utilizes a closed liquid‑cooled system that relies on conduction to transfer heat from the engine block into the liquid and then into the atmosphere by flowing coolant around the outside surface of each cylinder.
Suppose that, in a particular 4‑cylinder engine, each cylinder has a diameter of 8.75 cm, a height of 11.3 cm, and a thickness of 3.14 mm. The temperature on the inside of the cylinders is 195.2°C, and the temperature outside, where the coolant passes, is 130.0°C. The temperature of the incoming liquid (a mixture of water and antifreeze) is maintained at 95.0°C.
What volume flow rate of coolant [tex]\frac{V}{t}[/tex] would be required to cool this engine? Assume that the coolant reaches thermal equilibrium with the outer cylinder walls before exiting the engine. The specific heat of the coolant is 3.75 J/g°C and its density is 1.070×103 kg/m3. The cylinder walls have thermal conductivity of 1.10×102 W/m⋅∘C. Assume that no heat passes through the ends of the cylinders.
Answer:
thats a lot, which one u want me to do?
Explanation:
A hollow ball with a diameter of 3.81 cm has an average density of 0.0842 g/cm3. What force must be applied to hold it stationary while it is completely submerged under water? (Enter the magnitude in N, and select the direction from the options given.)
Answer:
0.26
Explanation:
Given that :
Diameter of ball = 3.81 cm = 3.81/100 = 0.0381 m
Radius (r) = 0.0381 / 2 = 0.01905 m
Average density of ball (Db) = 0.0842 g/cm³ = (0.0842 / 1000)kg / 10^-6 = 0.0842/ 1000 * 10^6 = 84.2kg/m³
Density of water (Dw) = 1000kg/m³
Volume of hollow ball: (4/3) * pi * r³
V = (4/3) * π * 0.01905^3
V = 0.0000289583 m³
Required force = (Dw * V * g) - (Db * V * g)
= (1000 * 0.0000289583 * 9.8) - (84.2 * 0.0000289583 * 9.8)
= 0.259896109172
= 0.2598 N
To determine the force that must be applied to the hollow ball to hold it stationary while it is completely submerged under water is 0.2243 Newton.
Given the following data:
Diameter of hollow ball = 3.81 cmDensity of hollow ball = 0.0842 [tex]g/cm^3[/tex]Density of water = 1000 [tex]kg/m^3[/tex]
Conversion:
Diameter of hollow ball = 3.81 centimeters to meters = [tex]\frac{3.81}{100} = 0.0381\;m[/tex]
Density of hollow ball = 0.0842 [tex]g/cm^3[/tex] to [tex]kg/m^3[/tex] = [tex]\frac{0.0842 \times 10^6}{1000} = 84.2 \;kg/m^3[/tex]
To determine the force that must be applied to the hollow ball to hold it stationary while it is completely submerged under water:
First of all, we would calculate the volume of the hollow ball by using the formula:
[tex]Volume = \frac{4}{3} \pi r^3\\\\Volume = \frac{4}{3} \times 3.142 \times 0.01905^3\\\\Volume = 4.19 \times 0.0000069\\\\Volume = 0.000029 \;m^3[/tex]
Next, we would find the force required for water and the hollow ball:
For water:
[tex]F_w = D_wVg\\\\F_w = 1000 \times 0.000029 \times 9.8\\\\F_w = 0.2842\; Newton[/tex]
For hollow ball:
[tex]F_h = D_hVg\\\\F_h = 84.2 \times 0.000029 \times 9.8\\\\F_h = 0.0239\; Newton[/tex]
Now, we can find the force that must be applied to the hollow ball:
[tex]Force = F_w - F_h\\\\Force = 0.2482 - 0.0239[/tex]
Force = 0.2243 Newton
Read more: https://brainly.com/question/18320053
A jet is flying from atlanta to gulfport and is cruising at Mach .79 or 844 km/hr. During the last 89 km it reduces its speed for landing at a rate of -2780 km/hr^2. How long will it take for the jet to reach landing speed? What was the landing speed of the jet?
Answer:
The time it takes for the jet to reach landing speed is approximately 0.136 hours which is approximately 489 seconds
The landing speed is approximately 466.365 km/hr
Explanation:
The given parameters are;
The initial cruising speed of the jet = Mach 0.79 = 844 km/hr
The rate of speed reduction in the last 89 km = -2780 km/hr²
The distance it takes the jet to reduce its speed for landing = 89 km
Given the above information, we make use of the following equation of motion;
s = u·t - 1/2·a·t²
v² = u² - 2·a·s
Where;
s = The distance over which the acceleration (deceleration) is applied = 89 km
u = The initial velocity = 844 km/hr
t = The time taken for the accelerating/decelerating motion
v = The final velocity (landing speed)
Substituting the values gives;
v² = 844² - 2·(2780)·89 = 217496
v = √217496 = 466.365 km/hr
v ≈ 466.365 km/hr
Therefore, the landing speed, v ≈ 466.365 km/hr
The time it takes is given by the equation, v = u - a·t
Therefore;
t = (u - v)/a = (844 - 466.365)/2780 ≈ 0.136 hours
The time it takes for the jet to reach landing speed ≈ 0.136 hours
From, s = u·t - 1/2·a·t², we have
89 = 844·t - 1/2 × 2780 × t²
89 = 844·t - 1390 × t²
1390 × t² - 844·t + 89 = 0
Solving with an online application gives;
t = 211/695 + (√(27187/2))/695 = 0.4715 hours or t = 211/695 - (√(27187/2))/695 = 0.136 hours
We note that the second time is for the time it will take the jet to get back to 89 km after reaching a speed of 0
Therefore, the correct time is t = 0.136 hours
The time it takes for the jet to reach landing speed ≈ 0.136 hours
A child walks 90 meters in 3 minutes . the speed in m/s
Answer:
Speed = 0.5 m/s
Explanation:
Time = 3min = 180 seconds
Distance = 90 meters
[tex]Speed =\frac{Distance}{Time} \\\\Speed= \frac{90}{180} \\\\Speed = \frac{1}{2} \\\\Speed =0.5\:m/s[/tex]
Answer:ttttrsc
Explanation:eeeeee
Density of solid copper is 8960 kg/metre cubed. Calculate the
volume of 5000 kg of copper to two significant figures.
Answer:
[tex]V=0.56~m^3[/tex]
Explanation:
Density
It's a measure of the mass of an object or substance per unit volume. It can be calculated as:
[tex]\displaystyle D=\frac{M}{V}[/tex]
Given the density of solid copper as [tex]D=8960~Kg/m^3[/tex], we will calculate the volume occupied by M=5000 Kg of copper solving the above equation for V:
[tex]\displaystyle V=\frac{M}{D}[/tex]
Substituting:
[tex]\displaystyle V=\frac{5000}{8960}[/tex]
Calculating:
[tex]V=0.558~m^3[/tex]
Expressed to two significant figures:
[tex]V=0.56~m^3[/tex]
The melting point of a substance is an example of?
Answer:
Melting point of a substance is the temperature at which a substance changes from a solid to a liquid. A change of state like melting is a physical change because it doesn’t alter the identity of the substance. In other words, melting point is a physical property because you can determine an object’s melting point without changing the substance. For example, when a substance like ice melts into water, the identity of the substance doesn’t change; the substance is water before and after the physical change. On the other hand, flammability is a chemical property because burning an object is a combustion reaction that leads to the creation of new substances. When you burn a piece of wood, it reacts with oxygen in the air to produce heat, light, carbon dioxide, and water vapor.
Explanation:
There are a lot of examples to choose from.
Which best explains the surface tension of water? capillary action cohesion adhesion sublimation
Answer:
Cohesion
Explanation:
Surface tension of water refers to the ability of the surface of water as a liquid to resist an external force. Surface tension of a liquid like water is dependent on the force of attraction that hold its molecules to one another, which is a force called COHESIVE FORCE.
Cohesion is a property of water characterized by the ability of water molecules to be attracted to one another. This cohesive property causes its molecules to be able to resist external forces or in other words is responsible for the SURFACE TENSION. Hence, the stronger the cohesive force between molecules of a liquid, the higher the surface tension.
What is the mass number of an atom that has 5 protons and 7 neutrons? I give brainliest.
Answer:
The atomic mass of an atom that has 5 protons and 7 neutrons would be 12.
Explanation:
In all cases, the number of protons added to the number of neutrons equate to the mass of an atom. Electrons do have mass, but it's so miniscule and insignificant that it doesn't contribute to the overall mass of the atom, so there's no need to count them.
Bonus Information:
DO NOT CONFUSE MASS WITH CHARGE! Protons and neutrons are the only particles that contribute to the mass of an atom. Meanwhile, protons (+) and electrons (-) are the only particles that have a charge. As it says in its name, neutrons are neutral or have no charge.
Remember:
C = p - e
M = p + n
C = atomic charge, M = atomic mass, p =protons, n = neutrons, e = electrons
I hope this helps!
Pick yourself around 1 situation (e.g. pushing a chair on the floor) with four different forces.
Display the situation by drawing object and forces who work between the object.
Write down the types of forces displayed.
Does this graph represent an endothermic or an exothermic reaction
Answer:
the graph represents an endothermic reaction
Explanation:
remember:
endo- inside
exo- out
A person with a mass of 40 kg is sitting on a box. What is the value of the normal force
normal force=mass*gravitational force
normal force=40*0
normal force=40
Rust, or iron oxide, ___________.
Group of answer choices
A is the result of rainwater and oxygen combining with iron
B leaves dark streaks across rocks
C is formed by chemical erosion
D All of the above.
Answer:
D
Explanation:
because all are reffering to the answer you need
a car is moving 18m/s to the east. if it takes the car 5 seconds to reach a velocity of 19 m/s to the east, what is its acceleration?
Kinematics
First Velocity (Vf) = 18 m/s
Last Velocity (Vl) = 19 m/s
time (t) = 5 seconds
acceleration = ______?
Answer :
Vl = Vf + a × t
19 = 18 + a × 5
19 - 18 = 5a
1 = 5a
1 / 5 = a
0,2 m/s² = a ✅
Answer: 0.2 m/s^2 east
Explanation:
A PE X
b.A certain piece of copper wire is determined to have a mass of 2.00 g per meter.
How many centimeters of the wire would be needed to provide 0.28 g of
copper?
Help please!!
Answer:
14cm
Explanation:
Mass per gram of the piece of wire;
2g of the wire is found in 1m
Since
100cm = 1m;
So;
100cm of the wire contains 2g of the wire
To provide 0.28g
Since;
2g of wire is made up of 100cm
0.28g of wire will be contained in [tex]\frac{100 x 0.28}{2}[/tex] = 14cm
14cm of the wire will contain 0.28g
Determine the average speed of a runner who runs 15 Km in one hour and 30 minutes
slope or velocit ime graph represent
2. What is instantaneous acceleration?
3. What is unit vector?
Answer:
Please check the explanation.
Explanation:
The slope of the velocity-time graph illustrates the change in velocity with respect to change in time.
In other words, the acceleration of the object is defined by the slope of a velocity graph. The acceleration can be obtained by finding the slope at a particular time.
Hence, the slope of the velocity time graph represent represents acceleration.
2. Also the acceleration of any object, like a car or bike, at some discrete instant in time 't' is termed as instantaneous acceleration which can be determined if we may take the derivate of the given velocity function.
3. A vector that has a direction and magnitude of 1 is termed as a unit vector, often called a direction vector.
The total weight of a car with passengers is 30,000N. The area of contact of each of the four tyres with the ground is 0.025m2. Determine the minimum car tyre pressure
Answer:
The minimum pressure car tire pressure is 300,000 Pa
Explanation:
Pressure
It's a measure of the force exerted by an object per unit surface:
[tex]\displaystyle P=\frac{F}{A}[/tex]
Where F is the force applied on a surface area A.
We are given the total weight of a car with passengers as Ft=30,000 N and we also know the area of contact of each tire with the ground as [tex]A=0.025 m^2[/tex].
The minimum pressure each tire can have is when the total weight is evenly distributed in all four tires, thus F=Ft/4=7,500 N.
Calculating the pressure:
[tex]\displaystyle P=\frac{7,500}{0.025}[/tex]
P=300,000 Pa
The minimum pressure car tire pressure is 300,000 Pa
Weathered rocks and soil are moved by _____?
A. Weathering
B. erosion
C. cycles
D. deposition
Answer:
The correct answer is B
True or false, transient hypertrophy is a result of short-term edema accumulation in the muscle?
Answer:
True
Explanation:
Someone is most likely to walk gingerly in order to do which of the following?
A.exercise his legs
B.trace his steps
C.keep from making noise
D.break in his shoes
I NEED HELP ASAP
Answer:
I think it a
Explanation:
Answer:
c
Explanation:
which list places different units of matter in the correct sequence from largest to smallest
Answer:
B: Human body, organs, molecules, atoms neutrons. please correct me if im wrong
Explanation:
A P ex
The list that places different units of matter in the correct sequence from largest to smallest is as follows:
The human body, organs, molecules, atoms neutrons.What is the matter?Matter may be defined as a type of substance that possesses a specific mass and occupies space by having a specific volume. So, it certainly has both mass and volume. In nature, each and every object is made up of matter.
With respect to the question, the human body is the largest unit that consists of matter. The body of a human generally consists of numerous organ systems which are built through the collection of other different organs.
The organ is further made up of the collection of tissues that are formed by the collection of cells. Cells possess numerous molecules which are made of atoms. Atoms have three types of subatomic particles, i.e. electrons, protons, and neutrons.
Therefore, the list that places different units of matter in the correct sequence from largest to smallest is well mentioned above.
To learn more about Matter, refer to the link:
https://brainly.com/question/16982523
#SPJ7
Your question seems incomplete. The most probable complete question is as follows;
Which list places different units of matter in the correct sequence from largest to smallest?
The human body, organs, molecules, atoms, and neutrons.Neutrons, atoms, molecules, organs, and the human body.Molecules, atoms, neutrons, human body, and organs.write any two methods of transport victim
simple methods to carry a sufferer encompass the four-hand seat, backpack carry, ski pole or tree limb backpack carry, and coiled rope seat. In the first method, two rescuers interlock hands. Each rescuer first grasps his right wrist with his left hand.
A 0.15 kg project hits the ground with a speed of 11 m/s. The project comes to rest in 0.015 seconds. What is the net force?
Answer:
Explanation:
ACCORDING TO NEWTONS SECOND LAW;
F = mass * acceleration
F = m(v-u/t)
m is the mass = 0.15kg
v is the final velocity = 11m/s
u is the initial velocity = 0m/s
t is the time = 0.015
Substitute;
F = 0.15(11-0)/0.015
F = 0.15(11)/0.015
F = 1.65/0.015
F = 110N
Hence the net force is 110N
What is power the quotient of?
A.speed and energy
B.work and time
C.speed and distance
D.work and distance
Power quotient of : _____?
Answer :
[tex]p = \frac{w}{t} [/tex]
P is Power (Watt)
W is Work (Joule)
T is Time (second)
So, it means Work and Time is the quotient of Power. (B)
Here photosynthesis in a nutshell. Can you explain what is happening?
Answer:
Photosynthesis is the process of using water, carbon dioxide and sunlight to produce sugar. The process of photosynthesis requires specialized cellular structures called chloroplasts to capture energy from the Sun and converted into chemical energy.
Explanation:
What is shown by the pattern of iron filings around these two magnets?
A. Opposite poles repel because no magnetic field forms between them.
B. Like poles attract because the magnetic field lines extend between them.
C. Like poles repel because the magnetic lined bend away from each other.
D. Opposite poles attract because the magnetic field lines cross each other.
The pattern of iron fillings around the magnet depicts that like poles repel because the magnetic lined bend away from each other. Thus, option C is correct.
What are magnetic field lines?The North Magnetic Pole would move via magnetic field lines, which are hypothetical lines. The magnet's oppositely polarized poles attract and repel one another.
Since the magnetic field lines inside the magnet run from the south pole to the north pole, Never do magnetic field lines cross one another. A closed loop is formed by magnetic field lines.
Because magnetic force lines are bending in the direction of the south pole in the illustration, like poles repel one another. If the magnetic lines are bent away from one another, like poles repel one another.
Thus, image given has the presence of lines bending away from each other, thereby are like poles repel. Hence, option C is correct.
Learn more about magnetic filed lines here:
https://brainly.com/question/15041207
#SPJ5
Please help ACTUALLY ANSWER i dont understand CER writing?
this is an example:
Claim: cookies are good because they are good
evidence : ¨cookies have 1 billion protien¨- the new york times
reasoning: (what would i put here???)
PLEASE HELP AND ACTUALLUY ANSWER
what is the KE if a 10kg mass traveling at 5 m/s
Answer: KE = 25 J
Explanation: You must use the formula
KE = 1/2 m v²
to solve this problem.
KE = 1/2 (10 Kg) (5 m/s)
KE = 1/2 (50 kgm/s)
KE = 25 J